In this paper, a single-stage rectifier-less boost converter circuit (SSRBC) for piezoelectric energy harvesting from ambient vibration was proposed. The proposed rectifier-less circuit acted as a boost converter to extract energy from a piezoelectric device (PD). It combined the conventional boost, buck-boost methods using two split inductors and single filter capacitor. The proposed integrated circuit topology functioned in both positive and negative half cycles generated by the PD. In the proposed topology, inductors were invigorated by being enveloped with the current, which was produced by the PD through the switches. This facilitated active rectification of ultra-low AC (amplitude < 0.5 V _P ). Theoretical analysis, control strategies, simulation and experimental study were presented. The proposed circuit was capable of converting a low amplitude AC voltage of 0.5 V _P into 5.1 V _dc . The highest output power extracted by the proposed circuit was 281.1 μW, which outperformed existing circuits. It could potentially facilitate the advancement of vibration-based energy harvesting systems for low power demand applications such as sensors, quartz watches and portable charging devices.

In recent years, piezoelectric materials have been widely investigated for harvesting energy from ambient vibrations. A vibrating piezoelectric device (PD) generates alternating current (AC), which needs to be converted into direct current (DC) for powering electronic devices or for storage. A traditional full-wave bridge rectifier (FBR) interface circuit serves this purpose, but it suffers from high power loss due to the presence of high forward voltage across the diodes. In this paper, an improved H-Bridge rectifier circuit is proposed as the AC-DC rectifier circuit to reduce power loss for high frequency and low amplitude application. The performance of the proposed rectifier circuit was experimentally studied, analysed and discussed. Two different testing scenarios for high frequency, namely, varying input power with fixed excitation frequency and varying excitation frequency with fixed input voltage were considered. Applicability of the circuit at low frequency range was also investigated. The outcome shows that the proposed circuit notably increases the voltage and the power produced from the PD when compared to traditional FBR circuits.

Harvesting energy from human motion for powering small scale electronic devices is attracting research interest in recent years. A piezoelectric device (PD) is capable of harvesting energy from mechanical motions, in the form of alternating current (AC) voltage. The AC voltage generated is of low frequency and is often unstable due to the nature of human motion, which renders it unsuitable for charging storage device. Thus, an electronic circuit such as a full bridge rectifier (FBR) is required for direct current (DC) conversion. However, due to forward voltage loss across the diodes, the rectified voltage and output power are low and unstable. In addition, the suitability of existing rectifier circuits in converting AC voltage generated by PD as a result of low frequency human motion induced non-sinusoidal vibration is unknown. In this paper, an improved H-Bridge rectifier circuit is proposed to increase and to stabilise the output voltage. To study the effectiveness of the proposed circuit for human motion application, a series of experimental tests were conducted. Firstly, the performance of the H-Bridge rectifier circuit was studied using a PD attached to a cantilever beam subject to low frequency excitations using a mechanical shaker. Real-life testing was then conducted with the source of excitation changed to a human performing continuous cycling and walking motions at a different speed. Results show that the H-Bridge circuit prominently increases the rectified voltage and output power, while stabilises the voltage when compared to the conventional FBR circuit. This study shows that the proposed circuit is potentially suitable for PEH from human motion.

This paper describes the design and practical application of a dual-stage H-Bridge (DSHBR) circuit to reduce the rectification losses and mitigate ripples in piezoelectric energy harvesting. The proposed DSHBR circuit integrates both AC-DC and DC-DC conversion processes using bidirectional switches and a step-up DC-DC converter, which applies to both positive and negative half cycles. One additional feature is that it does not require external power to turn on the bidirectional switches (V _th <; 0.3 V). Such feature facilitates active rectification at very low AC voltages (V _ac <; 0.5) generated by the piezoelectric device (PD). To validate the performance of the proposed circuit, a series of experimental tests were conducted. Firstly, the performance of circuit on rectifying the PD output was investigated using a shaker to generate high and low frequency excitations. Next, real-life testing was conducted with human arm motion as the source of excitation. Then, the ability of the entire system to charge solar batteries was investigated. The outcome shows that the DSHBR circuit prominently increased the rectified voltage and the output power while stabilising the DC voltage when compared with the conventional H-Bridge circuit.

In this study, a single stage rectifier-less electronic circuit (SSRBC) is presented for efficient energy harvesting using piezoelectric materials with low voltage. The proposed circuit eliminates the bridge rectification. In addition, it combines the topology of the boost and buck boost converter to regulate both positive and negative half cycles of the input AC voltage. Two inductors are used to reduce the stress in the switching operation. Using simulation software, A Novel Discontinuous Mode Piezoelectric Energy Harvesting Circuit for Low-Voltage Applications the proposed design is found to be able to rectify, boost, and regularise an input AC voltage of 0.5 V to 3.0 V. Applications include powering of low voltage applications, medical, robotics industries, quartz watches and mobile chargers. Modelling is carried out by using circuit design software LTSPICE.

This paper describes the detailed modelling of a vibration-based miniature piezoelectric device (PD) and the analysis modes of operation and control of a voltage doubler boost converter (VDBC) circuit to find the PD’s optimal operating conditions. The proposed VDBC circuit integrates a conventional voltage doubler (VD) circuit with a step-up DC-DC converter circuit in modes 1–4, while a non-linear synchronisation procedure of a conventional boost converter circuit is employed in modes 5–6. This integration acted as the voltage boost circuit without utilising duty cycles and complex auxiliary switching components. In addition, the circuit does not require external trigger signals to turn on the bidirectional switches. This facilitates the operation of VDBC circuit at very low AC voltage (V_ac ≥ 0.5 V). Besides this, the electrical characteristics of VDBC circuit’s input (i.e., PD) perfectly concurs with the studied testing scenarios using impedance power sources (mechanical shaker). Firstly, the proposed circuit which can rectify the PD’s output was tested at both constant input voltage with varying excitation frequency and constant excitation frequency with varying input voltage. Next, a small-scale solar battery was charged to validate the feasibility of the performance of the proposed VDBC circuit. The proposed circuit achieved a maximum output voltage of 11.7 V_dc with an output power of 1.37 mW. In addition, the rectified voltage waveform is stable due to the sminimisation of the ripples. In addition, the performance of VDBC circuit was verified by comparing the achieved results with previously published circuits in the literature. The results show that the proposed VDBC circuit outperformed existing units as described in the literature regarding output voltage and power. The developed rectifier circuit is suitable for various real-life applications such as energy harvesting and battery charging.