Many firms have carried out organisational change, such as mergers and acquisitions, to adapt to the rapidly changing business environment. During such changes, it is crucial for firms to provide an environment that will enhance employees’ psychological stability and commitment to change. Therefore, this study explores factors that increase employee commitment to change during mergers and acquisitions and identifies the process that forms commitment to change. To achieve the research goals, the study uses conservation of resources theory to extract factors that may influence employees’ commitment to change: three types of organisational justice are extracted as an organisational resource and psychological resilience (PR) is extracted as an individual resource. The study also applies psychological contract theory to extract mediators that link resources and employee commitment to change during the merger and acquisition process. The study empirically examines the research model using a structural equation model, based on 222 respondents who experienced mergers and acquisitions in South Korea. The three types of organisational justice and PR have positive relationships with affective commitment to change through the relational contract. Interactional justice, one type of organisational justice, and PR have negative relationships with continuance commitment to change through the transactional contract. This study may call human resource managers’ attention to the importance of employees’ psychological stability and may suggest possible ways to increase employees’ affective commitment to change in situations where there are frequent changes, such as mergers and acquisitions.
Recently, research regarding non-pneumatic tires that are resistant to punctures has been actively conducted, and the spoke structure design of non-pneumatic tires has been found to be a crucial factor. This study aimed to analyze the vertical stiffness characteristics of a non-pneumatic tire based on the shape of the spoke under the application of a vertical load. The three-dimensional model of a commercial non-pneumatic tire was obtained from the manufacturer (Kumho Tire Co., Inc., Gwangju, Korea), and the vertical stiffness characteristics of the three tire models with modified spoke shapes were compared and analyzed based on a reference tire model. Results show that the vertical stiffness of the fillet applied model is most appropriate. Furthermore, the vertical stiffness characteristics of the analyzed tire models indicate that if fillets with a minimum size are applied to the spokes, the stability of the non-pneumatic tire is expected to improve.
The necessity of hybrid vehicles and electric vehicles is widely known for reasons such as fossil fuel depletion, climate change, emission norms mandated by regulations, and so on. Expansion of the hybrid vehicle market is a realistic way to respond to fuel efficiency regulations. Hybrid electric vehicles are continuously challenged to meet cross-attribute performance while minimizing energy usage and component cost in a highly competitive automotive market. Current optimization strategy for a parallel hybrid requires much computational time and relies heavily on the drive cycle to accurately represent driving conditions in the future. With increasing application of the lithium-ion battery technology in the automotive industry, development processes and validation methods for the battery management system (BMS) have attracted attention. The purpose of this study is to propose an algorithm to analyze charging characteristics and improve accuracy for determining state of charge (SOC), the equivalent of a fuel gauge for the battery pack, during the regenerative braking period of a TMED type parallel hybrid electric vehicle.
Variable valve mechanisms are usually applied to a gasoline combustion engine to improve its power performance by controlling the amount of intake air according to the operating load. These mechanisms offer one possibility of resolving the conflict of objectives between a further reduction of raw emissions and an improvement in fuel efficiency. In recent years, variable valve control systems have become extremely important in the diesel combustion engine. Importantly, it has been shown that there are several potential benefits of applying variable valve timing (VVT) to a compression ignition engine. Valve train variability could offer one option to achieve the reduction goals of engine-out emissions and fuel consumption. The aim of this study was to investigate the effects on part load combustion and emission performance of internal exhaust gas recirculation (EGR) by variable exhaust valve lift actuation using a cam-in-cam system, which is an electronically variable valve device with a variable inside cam retarded to about 30 degrees. Numerical simulation based on GT-POWER has been performed to predict the NOx reduction strategy at the part load operating point of 1200 rpm in a four-valve diesel engine. A GT-POWER model of a common-rail direct injection engine with internal EGR was built and verified with experimental data. As a result, large potential for reducing NOx emissions through the use of exhaust valve control has been identified. Namely, it is possible to utilize heat efficiently as recompression of retarded post injection with downscaled specification of the exhaust valve rather than the intake valve, even if the CIC V1 condition with a reduction of the exhaust valve has a higher internal EGR rate of about 2% compared to that of the CIC V2 condition.
A diesel particulate filter (DPF) is an exhaust after-treatment device designed to capture and store exhaust particulate matter, such as soot and ash, to reduce emissions from diesel-powered vehicles. A DPF has a finite capacity and typically uses a substrate made of ceramic material that is formed into a honeycomb structure. Diesel particulate filters play an important role in diesel-fueled vehicles. Failure to maintain these filters can have significant consequences for vehicles. In this study, we investigated the failure type in cordierite DPF substrates. In addition, we experimentally characterized the particle number (PN) emission and on-board diagnostics (OBD) signal of a 2.0 L diesel-fueled vehicle generated by three types of DPF failure (crack, melting, and hollow). Specifically, X-ray photography analysis of the cordierite DPF was performed. The PN and OBD signals were assessed via the KD-147 vehicle driving mode and measured using a DMS-500 (PN measurement device) and global diagnosis tool (GDS) scanner (OBD diagnostic device), respectively. X-ray photography was used to characterize the internal structure of the three DPF-failure samples. A key result was that the maximum value of the OBD data, including airflow mass, boost pressure, and VGT actuator, was distinctly different for each DPF sample. The exhaust temperature gradient for the normal DPF and crack-damaged DPF followed the KD-147 driving pattern. This was because there was no volume damage inside the cordierite DPF substrates. However, in the case of the hollow and melting-damaged DPF, the volume inside the cordierite DPF substrates was reduced or the time for the exhaust gas to stay in the DPF substrates was decreased. The melting-damaged DPF continuously emitted the largest number of nanoparticles (of the order of 109 #/cc). This was regardless of the vehicle driving speed in the KD-147 driving mode. Eventually, an OBD-based algorithm to determine whether a DPF is damaged was derived in this study.
To mitigate global warming caused by vehicles, emission regulations have been implemented for all automobiles. Hybrid electric vehicles (HEVs) are being designed to meet consumer demand for eco-friendly vehicles that offer increased power and improved fuel efficiency. HEVs are powered by an internal combustion engine (ICE) in combination with one or more electric motors that use electrical energy stored in a secondary battery, which is typically a lithium-based battery. With the use of such a hybrid drivetrain system, the fuel efficiency can be improved over that of conventional ICE vehicles. In this study, we conducted a vehicle-driving experiment to evaluate a transmission-mounted electric device (TMED) type parallel HEV using a chassis dynamometer and on-board diagnostics (OBD) signal-measuring equipment. In addition, we performed a numerical analysis using the CRUISE vehicle simulation code with experimental data. In our analysis, the engine output, which affects the torque of the drive motor, and the capacity (energy density) of the lithium-ion polymer battery were set as variables that affect the fuel-economy performance. As a result of this numerical analysis, a hybrid power-drivetrain model based on CRUISE was developed, and the current balance was evaluated according to the change in the battery capacity. We found that the battery state of charge (SOC) dropped because of a decrease in battery capacity. Thus, we predicted that the lithium-ion battery capacity would be reduced.