Akari Hayashi

Prof. Akari Hayashi


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
TTTsuyoshi Takahashi
Tsuyoshi Takahashi
TITakuya Ikeda
Takuya Ikeda
KMKazuya Murata
Kazuya Murata
OHOsamu Hotaka
Osamu Hotaka
SHShigeki Hasegawa
Shigeki Hasegawa
KSKazunari Sasaki
Kazunari Sasaki
System durability is crucially important for the successful commercialization of fuel cell electric vehicles (FCEVs). Conventional accelerated durability testing protocols employ relatively high voltage to hasten carbon corrosion and/or platinum catalyst degradation. However, high voltages are strictly avoided in commercialized FCEVs such as the Toyota MIRAI to minimize these degradation modes. As such, conventional durability tests are not representative of real-world FCEV driving conditions. Here, modified start-stop and load cycle durability tests are conducted on prototype fuel cell stacks intended for incorporation into commercial FCEVs. Polarization curves are evaluated at beginning of test (BOT) and end of test (EOT), and the degradation mechanisms are elucidated by separating the overvoltages at both 0.2 and 2.2 A cm−2. Using our modified durability protocols with a maximum cell voltage of 0.9 V, the prototype fuel cell stacks easily meet durability targets for automotive applications, corresponding to 15-year operation and 200,000 km driving range. These findings have been applied successfully in the development of new fuel cell systems for FCEVs, in particular the second-generation Toyota MIRAI.

26 February 2023 in Journal of Power Sources
Verified
Journal Article
Closed access
YHYusuke Honsho
Yusuke Honsho
MNMayumi Nagayama
Mayumi Nagayama
JMJunko Matsuda
Junko Matsuda
KIKohei Ito
Kohei Ito
KSKazunari Sasaki
Kazunari Sasaki
AHAkari Hayashi
Akari Hayashi

9 January 2020 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
MYMasahiro Yasutake
Masahiro Yasutake
DKDaiki Kawachino
Daiki Kawachino
ZNZhiyun Noda
Zhiyun Noda
JMJunko Matsuda
Junko Matsuda
SLStephen Matthew Lyth
Stephen Matthew Lyth
KSKazunari Sasaki
Kazunari Sasaki
Novel catalyst-integrated gas diffusion electrodes (GDEs) for polymer electrolyte membrane water electrolysis (PEMWE) cells are presented, in which porous titanium microfiber sheets are etched in NaOH to generate a nanostructured TiO2 surface, followed by arc plasma deposition (APD) of iridium nanoparticles. The porous titanium sheet acts as a gas diffusion layer (GDL); the nanostructured TiO2 surface acts as a catalyst support with large surface area; and the iridium nanoparticles act as the electrocatalyst. The performance of these unique GDEs in PEMWE cells was optimized by etching in different NaOH concentrations to vary the nanostructure of the TiO2; and by varying the Ir loading via the number of APD pulses. The current-voltage characteristics and the durability of the optimized GDEs were comparable to those reported in the literature using conventional Ir-based electrocatalysts, and electrolysis was achieved with current density up to 5 A cm−2. The main advantages of this catalyst-integrated GDE include the very low iridium loading (i.e. around 0.1 mg cm−2, or just one-tenth of the loading typically used in conventional PEMWEs); high electrolysis current density; the fabrication of stacks with fewer components; and the fabrications of thinner stacks. This could ultimately lead to smaller and lower cost PEMWE systems.

10 December 2022 in Journal of Power Sources
Verified
Journal Article
Closed access
YHYasir Arafat Hutapea
Yasir Arafat Hutapea
MNMasamichi Nishihara
Masamichi Nishihara
ZGZulfi Al Rasyid Gautama
Zulfi Al Rasyid Gautama
AMAlbert Mufundirwa
Albert Mufundirwa
SLStephen Matthew Lyth
Stephen Matthew Lyth
AHAkari Hayashi
Akari Hayashi

11 September 2017 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
TITetsuji Itoh
Tetsuji Itoh
YSYuuta Shibuya
Yuuta Shibuya
AYAkira Yamaguchi
Akira Yamaguchi
YHYasuto Hoshikawa
Yasuto Hoshikawa
OTOsamu Tanaike
Osamu Tanaike
GSGalen D. Stucky
Galen D. Stucky
A large (40 mm ϕ) composite membrane with mesoporous silica nanotubes (F127MST) was coated with a thin carbon layer (1–2 graphene sheets) by carrying out chemical vapor deposition (CVD) using acetylene, and the obtained carbon-coated F127MST (C/F127MST) was used directly as an electrode. After evaluating the electrical conductivity inside the continuous mesopore network, the enzyme bilirubin oxidase (BOD) was loaded into the mesopores of C/F127MST to form BOD–C/F127MST. Indeed, this loading procedure was effective and achieved direct electron transfer between the enzymes and electrodes. The loading also was found to enhance the stability of stored BOD (it was stable for 15 days) and could be used to control the enzymatic reaction by varying the electric potential. We therefore consider BOD–C/F127MST to be a promising candidate as an effective bioelectrode in various fields.

1 January 2008 in Chemical Communications
Verified
Journal Article
Closed access
PDF file
KKKen’ichi Kimijima
Ken’ichi Kimijima
AHAkari Hayashi
Akari Hayashi
IYIchizo Yagi
Ichizo Yagi
A self-standing mesoporous carbon membrane (sOMC) with perpendicularly-ordered pore structures was prepared through a simple synthetic method; the pores with a diameter of 8 nm were well ordered over a large area and perpendicularly-oriented to the surface without any external field; in the formation of this ordered structure, the drying process is key, and a porous alumina support is important to induce drying.