Insoles play an important role in the conservative treatment of functional flat foot. The features of 3D-printed insoles are high customizability, low cost, and rapid prototyping. However, different designed insoles tend to have different effects. The study aimed to use 3D printing technology to fabricate three different kinds of designed insoles in order to compare the biomechanical effects on the lower extremities in flat foot participants. Ten participants with functional flat foot were recruited for this study. Data were recorded via a Vicon motion capture system and force plates during walking under four conditions: without insoles (shoe condition), with auto-scan insoles (scan condition), with total contact insoles (total condition), and with 5-mm wedge added total contact insoles (wedge condition). The navicular height, eversion and dorsiflexion angles of the ankle joint, eversion moment of the ankle joint, and adduction moment of the knee joint were analyzed, and comfort scales were recorded after finishing the analysis. Compared to the shoe condition, all three 3D printed insoles could increase the navicular height and ankle dorsiflexion angle and improve comfort. Among the three insoles, the wedge condition was the most efficient in navicular height support and increasing the ankle dorsiflexion angle.

Clinically, different foot arch heights are associated with different tissue injuries to the foot. To investigate the possible factors contributing to the difference in foot arch heights, previous studies have mostly measured foot pressure in either low-arched or high-arched feet. However, little information exists on stress variation inside the foot with different arch heights. Therefore, this study aimed to implement the finite element (FE) method to analyse the influence of different foot arches. This study established a 3D foot FE model using software ANSYS 11.0. After validating the FE model, this study created low-arched, high-arched and normal-arched foot FE models. The FE analysis found that both the stress and strain on the plantar fascia and metatarsal were higher in the high-arched foot, whereas the stress and strain on the calcaneous, navicular and cuboid were higher in low-arched foot. Additionally, forefoot pressure was increased with an increase in arch height.

Foot orthoses (FOs) are commonly used as interventions for individuals with flatfoot. Advances in technologies such as three-dimensional (3D) scanning and 3D printing have facilitated the fabrication of custom FOs. However, few studies have been conducted on the mechanical properties and biomechanical effects of 3D-printed FOs. The purposes of this study were to evaluate the mechanical properties of 3D-printed FOs and determine their biomechanical effects in individuals with flexible flatfoot. During mechanical testing, a total of 18 FO samples with three orientations (0°, 45°, and 90°) were fabricated and tested. The maximum compressive load and stiffness were calculated. During a motion capture experiment, 12 individuals with flatfoot were enrolled, and the 3D-printed FOs were used as interventions. Kinematic and kinetic data were collected during walking by using an optical motion capture system. A one-way analysis of variance was performed to compare the mechanical parameters among the three build orientations. A paired t-test was conducted to compare the biomechanical variables under two conditions: walking in standard shoes (Shoe) and walking in shoes embedded with FOs (Shoe+FO). The results indicated that the 45° build orientation produced the strongest FOs. In addition, the maximum ankle evertor and external rotator moments under the Shoe+FO condition were significantly reduced by 35% and 16%, respectively, but the maximum ankle plantar flexor moments increased by 3%, compared with the Shoe condition. No significant difference in ground reaction force was observed between the two conditions. This study demonstrated that 3D-printed FOs could alter the ankle joint moments during gait.

Mechanisms underlying exercise-induced muscle fatigue and recovery are dependent on peripheral changes at the muscle level and improper control of motoneurons by the central nervous system. In this study, we analyzed the effects of muscle fatigue and recovery on the neuromuscular network through the spectral analysis of electroencephalography (EEG) and electromyography (EMG) signals. A total of 20 healthy right-handed volunteers performed an intermittent handgrip fatigue task. In the prefatigue, postfatigue, and postrecovery states, the participants contracted a handgrip dynamometer with sustained 30% maximal voluntary contractions (MVCs); EEG and EMG data were recorded. A considerable decrease was noted in EMG median frequency in the postfatigue state compared with the findings in other states. Furthermore, the EEG power spectral density of the right primary cortex exhibited a prominent increase in the gamma band. Muscle fatigue led to increases in the beta and gamma bands of contralateral and ipsilateral corticomuscular coherence, respectively. Moreover, a decrease was noted in corticocortical coherence between the bilateral primary motor cortices after muscle fatigue. EMG median frequency may serve as an indicator of muscle fatigue and recovery. Coherence analysis revealed that fatigue reduced the functional synchronization among bilateral motor areas but increased that between the cortex and muscle.