Pattarawadee Poolperm

Ms. Pattarawadee Poolperm

Department of Industrial Engineering, Faculty of Engineering, Chiang Mai University
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in Materials Research Express
Verified
Journal Article
Open access
PDF file
PPPattarawadee Poolperm
Pattarawadee Poolperm
WNWasawat Nakkiew
Wasawat Nakkiew
NNNirut Naksuk
Nirut Naksuk
Simulations of the welding process for butt joints using finite element analysis (FEA) of the effect of porosity are presented. The metal used was aluminium alloy (grade 2024), and the filler material was alloy ER5356. The simulations were performed using the commercial software ANSYS, considering a double ellipsoid heat source, temperature-dependent material properties, material deposits, mechanical analysis, transient heat transfer, and defects (porosity). In this study, the FEA simulations were constructed for two types of heat source (single- and double-ellipsoid) used in gas tungsten arc welding (GTAW), and the calculated residual stress results were compared with the experimental values. Two double ellipsoid models were constructed for cases with and without porosity. The porosity was measured by three-dimensional (3D) computed tomography (CT), and the size and location of pores were mapped onto the weld bead created by the birth-and-death technique.

7 March 2021 in Materials
Verified
Journal Article
Open access
PDF file
PPPattarawadee Poolperm
Pattarawadee Poolperm
WNWasawat Nakkiew
Wasawat Nakkiew
NNNirut Naksuk
Nirut Naksuk
In this paper, we propose hot-wire plasma welding, a combination of the plasma welding (PAW) process and the hot-wire process in the additive manufacturing (AM) process. Generally, in plasma welding for AM processes, the deposit grain size increases, and the hardness decreases as the wall height increases. The coarse microstructure, along with the large grain size, corresponds to an increase in deposit temperature, which leads to poorer mechanical properties. At the same time, the hot-wire laser process seems to contain an overly high interstitial amount of oxygen and nitrogen. With an increasing emphasis on sustainability, the hot-wire plasma welding process offers significant advantages: deeper and narrow penetration than the cold-wire plasma welding, improved design flexibility, large deposition rates, and low dilution percentages. Thus, the hot-wire plasma welding process was investigated in this work. The wire used in the welding process was a titanium American Welding Society (AMS) 4951F (Grade 2) welding wire (diameter 1.6 mm), in which the welding was recorded in real time with a charge-coupled device camera (CCD camera). We studied three parameters of the hot-wire plasma welding process: (1) the welding speed, (2) wire current, and (3) wire feeding speed. The mechanical and physical properties (porosity, Vickers hardness, microstructure, and tensile strength) were examined. It was found that the number of layers, the length and width of the molten pool, and the width of the deposited bead increased, while the height of the layer increased, and the hot-wire current played an important role in the deposition. In addition, these results were benchmarked against specimens created by a hot-wire plasma welding/wire-based additive manufacturing process with an intention to develop the hot-wire PAW process as a potential alternative in the additive manufacturing industry.

6 October 2026 in Journal of Engineering and Applied Science
Verified
Journal Article
Open access
PDF file
PPPattarawadee Poolperm
Pattarawadee Poolperm
This research aims to study and develop the Wire Arc Additive Manufacturing (WAAM) process for titanium alloys utilizing the Hot-Wire Plasma Arc Welding (Hot-Wire PAW) technique. Due to titanium’s high susceptibility to oxidation during melting, a specialized inert gas shielding device was designed. Process optimization was subsequently conducted using a Full Factorial Design of Experiment (DOE) via Minitab software to determine the optimal parameters: a welding speed of 1.83 mm/s, a wire current of 35 A, and a wire feed rate of 0.85 m/min. Microstructural analysis utilizing the EDS technique confirmed the purity of the deposited titanium, indicating zero oxygen contamination. Furthermore, 3D microscopy revealed grain structure variations induced by the repeated thermal cycles inherent to the layer-by-layer deposition process. In-depth mechanical testing also exposed anisotropic behavior; specifically, tensile strength and ductility differed between the vertical and horizontal build directions, with horizontal specimens achieving an Ultimate Tensile Strength (UTS) of 560.80–693.58 MPa, compared to 631.65–677.10 MPa for vertical specimens. Additionally, Vickers hardness values ranged from 199.8 HV to 266.8 HV, demonstrating a decreasing trend along the height of the specimen. The findings of this study establish a crucial foundation for the cost-effective production of high-quality, large-scale titanium components for advanced industrial applications.