In this study, we proposed a method to improve the safety level of control software (CSW) by managing the CSW’s design information and safety analysis results, and combining failure mode and effects analysis (FMEA) and fault tree analysis (FTA). Here, the CSW is developed using structured analysis and design methodology. In the upper stage of the CSW’s development process, as the input of the preliminary design information (data flow diagrams (DFDs) and control flow diagrams (CFDs)), the causes of undesirable events of the CSW are clarified by FMEA, and the countermeasures are reflected in the preliminary design information. In the lower stage of the CSW’s development process, as the inputs of the detailed design information (DFDs and CFDs in the lower level) and programs, the causes of the specific undesirable event are clarified by FTA, and the countermeasures are reflected in the detailed design specifications and programs. The processes are repeated until the impact of undesirable events become the acceptable safety level. By applying the proposed method to the CSW installed into a communication control equipment on the space system, we clarified several undesirable events and adopted adequate countermeasures. Consequently, a safer CSW is developed by applying the proposed method.
There are many industrial products in our life, and the actions of those products are controlled by embedded control software (ECSW). Recently, many troubles have been caused by ECSW. To avoid those troubles, it is necessary to clarify the causes of the troubles and take countermeasures. However, the results of those tasks depend on the skills of the analyst. This paper proposes an analytic method that clarifies the causes of troubles by applying fault tree analysis (FTA) to the ECSW. The characteristics of the proposed method are as follows: Preparation of fault tree templates (FTTs) corresponding to instructions of the ECSW, and definition of the FT development rules by combining FTTs according to the back-tracing of the instruction execution process. By complying with the proposed method strictly, when an analyst who has studied computer science and safety engineering for 2–3 years conducts FTA, the analyst can obtain an appropriate result of FTA. This indicates that the safety level of ECSW will improve. As a result of applying the proposed method to existing ECSWs, we find that we can obtain the result of FTA at the appropriate level.
A simple method to separate soyasaponin Bb from a soy extract is presented. This method is based on the difference in the solubility of soyasaponin Bb and Ba and other components into 3:7 and 1:1 (v/v) acetone-water mixed solvents. The crude soyasaponin consisting of soyasaponins Aa, Ab, Ba, and Bb at the 10 wt% level and other components was examined as the soy extract. A 10 mg quantity of the crude soyasaponin was mixed with 1 mL of the 3:7 acetone-water containing 0.1 mol/L HCl, and the supernatant was removed to obtain a precipitate, which was found to contain mainly soyasaponins Bb and Ba. The precipitate was mixed with 0.4 mL of the 1:1 acetone-water containing 0.1 mol/L HCl; the supernatant was transferred, and was mixed with 0.6 mL of water to obtain a precipitate, which was found to contain mainly soyasaponin Bb. The yield was ca. 30%, which may be much higher than that by the conventional preparative chromatographic approach. The separation method is rapid and easy to carry out, and is useful for the preparation of a soyasaponin Bb sample.
19 April 2023 in SICE Journal of Control, Measurement, and System Integration
System Theoretic Process Analysis (STPA) is a method for analyzing hazards caused by interactions between components of an industrial product. STPA is applied in the upper stream stages of industrial product development, STPA detects hazards while referring to the whole configuration of the industrial product. Therefore, STPA generally does not deal with detailed information about the industrial product. Since the information on the industrial product is insufficient, it is difficult to clarify the factors of hazards, the occurrence order of factors, and the conditions that occur the hazard by STPA. Therefore, the following methods were added to the conventional STPA; the method of describing the components of industrial products in hierarchical detail, the method of clearly defining the behaviour of each component, and the method of tracking the structured CSD to clarify the causes of the hazard. By adding those methods, it became possible to conduct a hazard analysis of the industrial product in detail. As a result of applying the proposed method to the existing railroad crossing control system, it was confirmed that the proposed method could detect more factors of hazards and create adequate scenarios from the occurrence of hazard causes to the occurrence of the hazard.
23 November 2020 in Trends in Computer Science and Information Technology
This paper proposes an analysis method for hazards that are occurred by interactions between hardware and software when using an apparatus installed an Embedded Control Software (EBSW). Hazard means a state that negatively affects the apparatus when some bad conditions are satisfied. Especially, the purpose of the method is clarifying the EBSW portions that cause the hazards. The outline of the proposed method is as follows; (1)Develop EBSW specifications written in Unified Modeling Language (UML) and accident information, (2) Conduct safety analysis (System-theoretic Process Analysis: STPA) by inputting EBSW specifications and accident information, and generate the list of hazards and hazard scenarios, (3) Develop sequence diagrams corresponding to the hazard scenarios, and clarify program portions (Hazard Causal Factor: HCF) that are causes of the hazards, and (4) Conduct Failure Mode and Effects Analysis (FMEA), and apply countermeasures to avoid occurrences of the hazards. As a result of applying this method to the sample EBSW, we can confirm that the safety EBSW is developed.