Center of Vehicles for Sustainable Mobility, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, 166 07 Praha 6, Czech Republic
Prof. Dr. Jan Macek
Center of Vehicles for Sustainable Mobility, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, 166 07 Praha 6, Czech Republic
The goal of the paper is to discuss specific features of the in-cylinder heat transfer calculation based on widely used empirical formulas. The potential of in-house codes compared with commercially available software packages is presented. The principles of user models in the GT-SUITE environment are also explained. The results of calibrated models are briefly discussed.
20 December 2017 in Journal of Middle European Construction and Design of Cars
The current study evaluates the predictive capabilities of a new phenomenological combustion model, available as a part of the GT-Suite software package. It is comprised of two main sub-models: 0D model of in-cylinder flow and turbulence, and turbulent SI combustion model. The 0D in-cylinder flow model (EngCylFlow) uses a combined K-k-ε kinetic energy cascade approach to predict the evolution of the in-cylinder charge motion and turbulence, where K and k are the mean and turbulent kinetic energies, and ε is the turbulent dissipation rate. The subsequent turbulent combustion model (EngCylCombSITurb) gives the in-cylinder burn rate; based on the calculation of flame speeds and flame kernel development. This phenomenological approach reduces significantly the overall computational effort compared to the 3D-CFD, thus allowing the computation of full engine operating map and the vehicle driving cycles. Model was calibrated using a full map measurement from a turbocharged natural gas SI engine, with swirl intake ports. Sensitivity studies on different calibration methods, and laminar flame speed sub-models were conducted. Validation process for both the calibration and sensitivity studies was concerning the in-cylinder pressure traces and burn rates for several engine operation points achieving good overall results.
1 December 2016 in Journal of Middle European Construction and Design of Cars
The goal of the contribution is to describe the process of measurement on a twin entry turbocharger turbine, and evaluation of obtained data. A specific feature of the twin entry turbine measurement is the separation of turbine sections. It is necessary to control different conditions in each section to achieve partial admission of the turbine impeller. The results are fundamental for the calibration process of a developed physical 1-D model of a radial turbine with twin scroll.
1 June 2016 in Journal of Middle European Construction and Design of Cars
This research uses 1-D simulation in GT-Power for evaluation of boosting systems for a spark ignition engine. Exhaust gas driven (waste-gated turbocharger) and mechanical driven (Roots blower) boosting systems are assessed in both steady state and transient modes in terms of performance, efficiency, fuel consumption, drivability, energy distribution and other aspects that influence gas exchange phase. Moreover, different boost control strategies, particularly at partial load, are also evaluated. Results of the research are aimed at helping identify an optimal boosting system for standardized or real-world drive cycles.
1 June 2013 in Journal of Middle European Construction and Design of Cars
Shrnutí Članek, na několika přikladech, popisuje simulace s využitim 1-D modelu radialni turbiny turbodmychadla. Cilem je popsat současny stav a ukazat potencial 1-D přistupu v oblasti modelovani turbodmychadla. Pro možnost testovani modelů turbiny a kompresoru byly vyvinuty rozmanite simulačni nastroje. Model turbinoveho testovaciho stavu umožňuje provozovat turbinu v široke provozni oblasti. Model zkušebniho stavu turbodmychadel se spalovaci komorou je vhodny pro přiřazeni kompresoru turbině. Članek uzaviraji vysledky fungovani modelu turbiny ve spojeni s modelem virtualniho čtyřtaktniho zažehoveho motoru.
1 December 2013 in Journal of Middle European Construction and Design of Cars
SHRNUTÍ Tato studie popisuje vliv změny indikovane učinnosti vysokotlake časti pracovniho cyklu (hiHP) na indikovanou učinnost celeho cyklu (hi) a pumpovnich ztrat (pro udrženi konstantni hodnoty středniho efektivniho tlaku) pro připad zažehoveho motoru škrceneho v sacim traktu v nizkem zatiženi. Za učelem zjištěni těchto zavislosti byl sestrojen jednoduchy matematicky model. Model umožňuje počitat vztahy mezi indikovanou učinnosti vysokotlake časti pracovniho cyklu, indikovanou učinnosti celeho cyklu a take středni hodnotou tlaku v průběhu saciho zdvihu pistu (ps). Navrženy model byl kalibrovan a nasledně verifikovan pomoci experimentalně pořizenych dat. Experimentalni prace byly provedeny na testovacim zažehovem, čtyřvalcovem motoru s pohonem na zemni plyn, pracujici se stechiometrickou koncepci a vybavenym take třicestnym katalyzatorem. Cilem experimentů bylo navic najit řešeni pro dalši zvyšeni učinnosti vysokotlake časti v porovnani s optimalnim konvenčnim nastavenim motoru. I když samozřejmě existuje jednoduchy způsob pro změnu (sniženi) hodnoty indikovane učinnosti vysokotlake časti pracovniho cyklu pouhym rozladěnim optimalni hodnoty předstihu zažehu, tato varianta nebyla cilem vyzkumu autorů. Z tohoto důvodu byla pro tento učel ve finale zvolena varianta s aplikaci specialni zapalovaci svičky do každeho valce motoru. Jak ze simulaci tak z experimentů bylo zjištěno, že se zvyšenim indikovane učinnosti vysokotlake časti pracovniho cyklu dochazi ke zvyšeni jak indikovane učinnosti celeho cyklu tak take pumpovnich ztrat a obraceně, což se předpokladalo.