Paweł Wojewoda

Dr. Paweł Wojewoda

Automotive Vehicles and Transport Engineering, Rzeszów University of Technology, Rzeszów, Podkarpackie, Poland
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
Artur JaworskiArtur Jaworski
Artur Jaworski
Maksymilian MądzielMaksymilian Mądziel
Maksymilian Mądziel
KLKrzysztof Lew
Krzysztof Lew
Tiziana CampisiTiziana Campisi
Tiziana Campisi
Paweł WośPaweł Woś
Paweł Woś
MJMirosław Jakubowski
Mirosław Jakubowski
Among the solutions that make it possible to reduce CO2 emissions in the transport sector, particularly in urban traffic conditions, are hybrid vehicles. The share of driving performed in electric mode for hybrid vehicles is highly dependent on motion resistance. There are different methods for determining the motion resistance function during chassis dynamometer testing, leading to different test results. Therefore, the main objective of this study was to determine the effect of the chassis dynamometer load function on the energy demand and CO2 emissions of a full-hybrid passenger car. Emissions tests according to the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer for three different methods of determining the car’s resistance to motion. The study showed that adopting the motion resistance function according to different methods, results in differences in CO2 emissions up to about 35% for the entire cycle. Therefore, the authors suggest that in the case of tests carried out with chassis dynamometers, it is necessary to also provide information on the chassis dynamometer loading function adopted for the tests.

15 September 2020 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
Artur JaworskiArtur Jaworski
Artur Jaworski
Maksymilian MądzielMaksymilian Mądziel
Maksymilian Mądziel
HKHubert Kuszewski
Hubert Kuszewski
KLKazimierz Lejda
Kazimierz Lejda
KBKrzysztof Balawender
Krzysztof Balawender
AUAdam Ustrzycki
Adam Ustrzycki
The exhaust emission from modern vehicles is reduced by catalysts except for cold start phase. The difference in emissions for unheated catalysts is large and can reach several times higher than the emission for the heated thermal state of the engine. In the dyno tests, the analysis of the duration and volume of the emissions for harmful exhaust components: CO2 (carbon dioxide), CO (carbon monoxide), THC (total hydrocarbons), NOx (nitrogen oxides) at various climatic chamber operating temperatures, i.e. 0-30oC, for a vehicle meeting the EURO3 and EURO6 standards was performed. Stationary analyzers AVL AMA i60 were used to measure the emissions. The article presents the differences in the emissions for the cold-start phase of engine operation and the duration of time passing to a heated engine for vehicles powered by petrol and LPG (liquefied petroleum gas). The work shows the analysis of modal emissions as well as bag emission.

31 July 2023 in Energies
Verified
Journal Article
Open access
PDF file
Artur JaworskiArtur Jaworski
Artur Jaworski
Hubert KuszewskiHubert Kuszewski
Hubert Kuszewski
KLKrzysztof Lew
Krzysztof Lew
Paweł WojewodaPaweł Wojewoda
Paweł Wojewoda
KBKrzysztof Balawender
Krzysztof Balawender
SBSergii Boichenko
Sergii Boichenko
Differences between the results obtained in laboratory and road tests of vehicles depend on a number of factors. Among the most important of these are driving cycle and road load. These parameters also affect the hybrid drive control, including the combustion engine operation or driving in electric mode. In most studies, tests carried out on chassis dynamometers concern type approval cycles (NEDC—New European Driving Cycle, WLTC—World-wide harmonized Light duty Test Cycle, FTP— Federal Test Procedure), which differ from real on-road tests. Consequently, the different driving cycles do not allow for results similar to those obtained during on-road driving, especially as the actual cycles on the road are unrepeatable. It is also important to determine the effect of the motion resistance function adopted for chassis dynamometer tests on exhaust emissions and fuel consumption. For this purpose, the authors tested a hybrid car under road and laboratory conditions for the same driving cycle. The analysis was conducted for an example urban road cycle in Rzeszow (URRC). The purpose of the study was to determine the differences in the results of gaseous emissions (THC, CO, CO2, NOx) and fuel consumption (energy) of a hybrid car under road conditions, with the results of tests conducted on a chassis dynamometer, for the same cycle and three functions of resistance.

11 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
KBKrzysztof Balawender
Krzysztof Balawender
KLK Lew
K Lew
DKD Konieczny
D Konieczny
Kazimierz LejdaKazimierz Lejda
Kazimierz Lejda
AUAdam Ustrzycki
Adam Ustrzycki
Paweł WojewodaPaweł Wojewoda
Paweł Wojewoda
The article presents the results of comparative research on the utility and ecological parameters of the FSO 1.6 GSi engine, which are the effect of using additional injectors in the intake manifold. In the future, these injectors will be responsible for supplying the engine with alternative fuels. Engine parameters such as: cylinder filling factor, torque, unit fuel consumption and exhaust composition were analyzed. The tests were carried out with both standard and modified collector, in which additional injectors were installed.

3 October 2025 in Combustion Engines
Verified
Journal Article
Open access
KLKrzysztof Lew
Krzysztof Lew
Paweł WojewodaPaweł Wojewoda
Paweł Wojewoda
JLJanusz Lubas
Janusz Lubas
The purpose of the research presented in this article was to determine the impact of the storage period of engine and transmission oils on their operational properties. The prolonged storage of oils leads to a series of physicochemical changes that can significantly affect their lubrication efficiency. Changes such as reduced viscosity, changes in density, and deterioration in lubricity can lead to increased wear of the engine, transmission, and other mechanical components. The study included samples of new and five-year-old engine and transmission oils, as well as engine oil after the break-in period (with a mileage of approximately 800 km). The SAE 10W40 oil after use in an internal combustion engine shows a significant reduction in scuffing resistance (approximately one-third lower scuffing load compared to new and old oil). Long-term five-year storage also slightly reduces its scuffing resistance at higher temperatures. In contrast, long-term storage of SAE 30 oil significantly decreases its scuffing resistance across both tested temperature ranges (by about 20%). Storage time did not significantly alter the viscosity index of SAE 10W40, whereas old SAE 30 oil showed a slightly better index than new oil.

1 November 2017 in Combustion Engines
Verified
Journal Article
Open access
KBKrzysztof Balawender
Krzysztof Balawender
DKDariusz Konieczny
Dariusz Konieczny
HKHubert Kuszewski
Hubert Kuszewski
KLKazimierz Lejda
Kazimierz Lejda
KLKrzysztof Lew
Krzysztof Lew
Paweł WojewodaPaweł Wojewoda
Paweł Wojewoda
The objective of the research results of which are presented in this paper was to determine the effect of selected physicochemical properties of fuels on ecological parameters of a diesl engine. Physicochemical parameters of fuel have a decisive effect on correct functioning, operating parameters, and cleanliness of the exhaust gas emitted to the environment by any combustion engine. Results of physicochemical studies can be useful in developing fuels blends of specific properties, whereas results obtained in the course of tests carried out on an engine test bench allow to optimize parameters of the fuel injection process with the aim to reduce emissions of toxic compounds to atmosphere.