Satoshi Ogata

Dr. Satoshi Ogata

Department of Mechanical Systems Engineering, Tokyo Metropolitan University, Tokyo 192-0397, Japan
orcid

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2008 in Journal of Colloid and Interface Science
Verified
Journal Article
Closed access
KYKen Yamamoto
Ken Yamamoto
SOSatoshi Ogata
Satoshi Ogata

1 March 2013 in International Journal of Multiphase Flow
Verified
Journal Article
Closed access
KYKen Yamamoto
Ken Yamamoto
SOSatoshi Ogata
Satoshi Ogata

1 August 2003 in AIChE Journal
Verified
Journal Article
Closed access
PDF file
KWKeizo Watanabe
Keizo Watanabe
TTTsukasa Takayama
Tsukasa Takayama
SOSatoshi Ogata
Satoshi Ogata
SISeiji Isozaki
Seiji Isozaki

1 September 2005 in AIChE Journal
Verified
Journal Article
Closed access
PDF file
SOSatoshi Ogata
Satoshi Ogata
YOYoshihisa Osano
Yoshihisa Osano
KWKeizo Watanabe
Keizo Watanabe

14 February 2021 in Processes
Verified
Journal Article
Open access
PDF file
SOSatoshi Ogata
Satoshi Ogata
RNRyo Nakanishi
Ryo Nakanishi
A liquid droplet can hover over a solid surface that is heated above the Leidenfrost point (LFP), at which an insulating vapor layer is formed that acts as a heat transfer barrier. Recent studies have reported that hierarchical micro- and nanoscale textures provide high wettability and significant LFP enhancement. However, such textures are often difficult and expensive to fabricate. Therefore, this study aimed to experimentally demonstrate LFP enhancement through the use of low-cost hierarchical textures. Surface textures were fabricated by coating SiO2 nanoparticles on stainless steel wire meshes. The droplet lifetime method was used to determine the LFP in a temperature range of 200 °C–490 °C. High-speed imaging (4000–23,000 fps) was performed for visualizing the impact behavior of a droplet. The LFP value of the nanocoated mesh surface was found to be greater than 490 °C. This enhanced LFP was 178 °C higher than that of a stainless steel surface and 38 °C higher than that of a single-layer textured surface. Furthermore, with respect to the LFP enhancement, the explosive impact behavior of a droplet can be observed on nanocoated mesh surfaces.

13 December 2022 in Fluids
Verified
Journal Article
Open access
PDF file
SOSatoshi Ogata
Satoshi Ogata
YMYuichiro Murata
Yuichiro Murata
For potential use in wastewater management and health control, this study investigates the disinfection effectiveness of bulk ultrafine bubbles (UFBs) with different bubble number densities and solution pH. Initially, neutral UFB solutions with different bubble concentrations were mixed with E. coli suspension for 120 min, but these solutions did not achieve sterilization. The bubble number density did not affect the disinfection ability of the neutral solution. Next, the pH of the UFB solutions was fixed at 5, 7, and 9. When mixed with E. coli suspension, the acidic UFB solutions reduced the colony counts by 12% after 30 min of cultivation and by 66% after 60 min of cultivation. The colony counts increased slightly in neutral and significantly in alkaline UFB solutions. The acidic UFB solutions had lower zeta potentials and smaller number densities after cultivation, implying that the number density reduced through bubble coalescence rather than increased by bubble collapse. Additionally, the UFBs exhibited insignificant fluorescence intensity, suggesting that the colony counts increased by generated ∙OH radicals. This study revealed that the effect of UFB on E. coli significantly depends on the solution pH. Further, an acidified solvent achieves a bactericidal effect, whereas a neutral or alkaline solvent enhances the growth effect. This result is important when using actual wastewater.