Piezoresistive sensors are among the earliest micromachined silicon devices. The need for smaller, less expensive, higher performance sensors helped drive early micromachining technology, a precursor to microsystems or microelectromechanical systems (MEMS). The effect of stress on doped silicon and germanium has been known since the work of Smith at Bell Laboratories in 1954. Since then, researchers have extensively reported on microscale, piezoresistive strain gauges, pressure sensors, accelerometers, and cantilever force/displacement sensors, including many commercially successful devices. In this paper, we review the history of piezoresistance, its physics and related fabrication techniques. We also discuss electrical noise in piezoresistors, device examples and design considerations, and alternative materials. This paper provides a comprehensive overview of integrated piezoresistor technology with an introduction to the physics of piezoresistivity, process and material selection and design guidance useful to researchers and device engineers.

Wireless power transmission was conceptualized nearly a century ago. Certain achievements made to date have made power harvesting a reality, capable of providing alternative sources of energy. This review provides a summ ary of radio frequency (RF) power harvesting technologies in order to serve as a guide for the design of RF energy harvesting units. Since energy harvesting circuits are designed to operate with relatively small voltages and currents, they rely on state-of-the-art electrical technology for obtaining high efficiency. Thus, comprehensive analysis and discussions of various designs and their tradeoffs are included. Finally, recent applications of RF power harvesting are outlined.

We have developed a single-wafer vacuum encapsulation for microelectromechanical systems (MEMS), using a thick (20-mum) polysilicon encapsulation to package micromechanical resonators in a pressure 600 cycles of -50 to 80degC, and no measurable change in cavity pressure was seen. We have also performed accelerated leakage tests by driving hydrogen gas in and out of the encapsulation at elevated temperature. Two results have come from these hydrogen diffusion tests. First, hydrogen diffusion rates through the encapsulation at temperatures 300-400degC have been determined. Second, the package was shown to withstand multiple temperature cycles between room and 300-400degC without showing any adverse affects. The high robustness and stability of the encapsulation can be attributed to the clean, high-temperature environment during the sealing process

Packaging of micro-electro-mechanical systems (MEMS) devices has proven to be costly and complex, and it has been a significant barrier to the commercialization of MEMS. We present a packaging solution applicable to several common MEMS devices, such as inertial sensors and micromechanical resonators. It involves deposition of a 20 /spl mu/m layer of epi-polysilicon over unreleased devices to act as a sealing cap, release of the encapsulated parts via an HF vapor release process, and a final seal of the parts in 7 mbar (700 Pa) vacuum. Two types of accelerometers, piezoresistive and capacitive sensing, were fabricated. Piezoresistive accelerometers with a footprint smaller than 3 mm/sup 2/ had a resolution of 10 /spl mu/g//spl radic/Hz at 250 Hz. Capacitive accelerometers with a 1 mm/sup 2/ footprint had a resolution of 1 mg/spl radic/Hz over its 5 kHz bandwidth. Resonators with a quality factor as high as 14,000 and resonant frequency from 50 kHz to 10 MHz have also been built. More than 100 capacitive accelerometers and 100 resonators were tested, and greater than 90% of the resonators and accelerometers were functional.

Thermoelastic dissipation (TED) is analyzed for complex geometries of micromechanical resonators, demonstrating the impact of resonator design (i.e., slots machined into flexural beams) on TED-limited quality factor. Zener first described TED for simple beams in 1937. This work extends beyond simple beams into arbitrary geometries, verifying simulations that completely capture the coupled physics that occur. Novel geometries of slots engineered at specific locations within the flexural resonator beams are utilized. These slots drastically affect the thermal-mechanical coupling and have an impact on the quality factor, providing resonators with quality factors higher than those predicted by simple Zener theory. The ideal location for maximum impact of slots is determined to be in regions of high strain. We have demonstrated the ability to predict and control the quality factor of micromechanical resonators limited by thermoelastic dissipation. This enables tuning of the quality factor by structure design without the need to scale its size, thus allowing for enhanced design optimization