Aiming to improve the reliability and durability of lithium-ion battery systems, a hybrid electrical circuit model (ECM) and two-dimensional grid long short-term memory (2D-GLSTM) neural network-based cell core temperature estimation technique is proposed in this paper to leverage their respective strengths. The ECM is used to estimate the total heat generation (Q) inside the cell using the measured physical parameters such as voltage, current, and temperature. Further, the value of Q and other external measurements are used by the 2D-GLSTM neural network (deep learning approach) to estimate the core temperature of the battery cell. An experimentally validated Kalman filter and equivalent electrothermal model are used to generate a large quantity of training and testing data, under a wide range of dynamic loading and ambient temperature to validate the proposed concept. The results showed that the proposed technique can achieve root-mean-squared-error of less than 1% with unknown test data which is quite satisfactory for practical applications. A comparative study with the state-of-the-art techniques in core temperature estimation showed that the proposed scheme performed better. The highly accurate prediction results under a comprehensive operating condition confirm the reliability and generalization ability with solid robustness to the external uncertainties.
Electric Vehicles (EV) and Hybrid EV (HEV) use Lithium (Li) ion battery packs to drive them. These battery packs possess high specific density and low discharge rates. However, some of the limitations of such Li ion batteries are sensitivity to high temperature and health degradation over long usage. The Battery Management System (BMS) protects the battery against overvoltage, overcurrent etc., and monitors the State of Charge (SOC) and the State of Health (SOH). SOH is a complex phenomenon dealing with the effects related to aging of the battery such as the increase in the internal resistance and decrease in the capacity due to unwanted side reactions. The battery life can be extended by estimating the SOH accurately. In this paper, an extensive review on the effects of aging of the battery on the electrodes, effects of Solid Electrolyte Interface (SEI) deposition layer on the battery and the various techniques used for estimation of SOH are presented. This would enable prospective researchers to address the estimation of SOH with greater accuracy and reliability.
This paper deals with the estimation of core temperature (Tc) of a Lithium (Li) ion battery using measured ambient and surface temperatures. The temperatures were measured using thermocouples placed at appropriate locations. A second order thermal model was considered for the core temperature (Tc) estimation. A set of coupled linear ordinary differential equations (ODEs) were obtained by applying Kirchhoff’s current and voltage laws to the thermal model. The coupled ODEs were redefined in the discrete state space representation. The thermal model did not account for small changes in surface temperature (Ts). MATLAB/Simulink were used for modelling a Kalman filter with appropriate process and measurement noise levels. It was found that the temperatures closely followed the current patterns. For high currents, Tc dominated the surface temperature by about 3 K. Tc estimation plays a very important role in designing an effective thermal management and maintaining the state of health (SOH) during fast discharges under limits. Most of the battery management system (BMS) applications required Ts as the input to the controller. Hence, an inverse calculation for estimating Ts from known Tc was carried out and found to be reasonably accurate. It was found that the thermal parameter Cs played a major role in the accuracy of Ts prediction and must have low values to minimize errors.
The incorporation of renewable energy sources into smart grid systems does basically signify a significant move of achieving sustainable energy consumption and management. On the contrary, due to the unpredictability of renewables and the energy grids’ increased complexity, there remain certain issues to be tackled. This study explores enhancing of the capacity of energy to be derived from renewable sources through IoT linked management systems. Through the utilization of modern IoT technologies which contribute towards maximizing the effectiveness of smart grid operations the study aims to accomplish this thereby enhancing the efficiency, reliability, sustainability of smart grids, which in turn facilitate the balancing of energy supply and demand and optimal energy distribution followed by the ready integration of renewable energy sources. This paper focuses on a holistic solution that includes the utilization of IoT sensors and devices to perform real-time energy monitoring, devising smart algorithms for an energy management system, and harnessing the power of cloud computing to analyze data. This part involves implementation explaining the practical steps done to work out the framework: system’s architecture design, IoT devices selection, data management activities and the control mechanism’s integration. Simulation results represent the ability of distributed IoT systems to advance smart grid practices by showing a decrease in energy transportation losses, AC grid stability and the integration of RES potential. Problems that come up during the course of project, like scalability and security, are described, and solutions to those problems proposed.
Estimation of core temperature is one of the crucial functionalities of the lithium-ion Battery Management System (BMS) towards providing effective thermal management, fault detection and operational safety. It is impractical to measure the core temperature of each cell using physical sensors, while at the same time implementing a complex core temperature estimation strategy in onboard low-cost BMS is also challenging due to high computational cost and the cost of implementation. Typically, a temperature estimation scheme consists of a heat generation model and a heat transfer model. Several researchers have already proposed ranges of thermal models with different levels of accuracy and complexity. Broadly, there are first-order and second-order heat resistor–capacitor-based thermal models of lithium-ion batteries (LIBs) for core and surface temperature estimation. This paper deals with a detailed comparative study between these two models using extensive laboratory test data and simulation study. The aim was to determine whether it is worth investing towards developing a second-order thermal model instead of a first-order model with respect to prediction accuracy considering the modeling complexity and experiments required. Both the thermal models along with the parameter estimation scheme were modeled and simulated in a MATLAB/Simulink environment. Models were validated using laboratory test data of a cylindrical 18,650 LIB cell. Further, a Kalman filter with appropriate process and measurement noise levels was used to estimate the core temperature in terms of measured surface and ambient temperatures. Results from the first-order model and second-order models were analyzed for comparison purposes.