Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.
In this letter, we propose relay-based positioning in time division multiple access (TDMA) networks, called RPT. Although the concept of relay-based positioning is an improvement over the performance of relative navigation (RelNav), there are two problems to be solved when applying the relay concept to a TDMA network. First, measurement errors caused by mobility may degrade user accuracy because positioning references transmit navigation messages at their assigned times in TDMA, unlike conventional navigation systems, where all references continuously transmit. Second, a selection algorithm among airborne nodes is needed to relay messages to users. An RPT frame is designed to assign the slots for the broadcast and relay of navigation messages consecutively to minimize the effect of mobility. The selection algorithm determines the optimum set of airborne relays by selecting evenly distributed nodes depending on their distances to the master station. The simulation results indicate that RPT significantly improves user accuracy over RelNav.
31 January 2016 in The Journal of Korean Institute of Communications and Information Sciences
The airborne relay-based positioning system (ARPS), which employs the relaying of navigation signals, was proposed as an alternative positioning system. However, the ARPS has limitations, such as relatively large vertical error and service restrictions, because firstly, the user position is estimated based on airborne relays that are located in one direction, and secondly, the positioning is processed using only relayed navigation signals. In this paper, we propose an enhanced positioning algorithm to improve the performance of the ARPS. The main idea of the enhanced algorithm is the adaptable use of either virtual or direct measurements of reference stations in the calculation process based on the structural features of the ARPS. Unlike the existing two-step algorithm for airborne relay and user positioning, the enhanced algorithm is divided into two cases based on whether the required number of navigation signals for user positioning is met. In the first case, where the number of signals is greater than four, the user first estimates the positions of the airborne relays and its own initial position. Then, the user position is re-estimated by integrating a virtual measurement of a reference station that is calculated using the initial estimated user position and known reference positions. To prevent performance degradation, the re-estimation is performed after determining its requirement through comparing the expected position errors. If the navigation signals are insufficient, such as when the user is outside of airborne relay coverage, the user position is estimated by additionally using direct signal measurements of the reference stations in place of absent relayed signals. The simulation results demonstrate that a higher accuracy level can be achieved because the user position is estimated based on the measurements of airborne relays and a ground station. Furthermore, the service coverage is expanded by using direct measurements of reference stations for user positioning.
The universal access transceiver (UAT) is interesting as an alternative pseudolite because pseudoranging is available using ground segment messages. However, there is a limitation that accurate ranging is not supported when the user altitude is low, because of geometrical and multipath effects. In this study, we investigated the application of the airborne relay-based positioning system (ARPS) to UAT, because the ARPS has the advantages of a ground-based and an airborne-based system and is well suited to the UAT frame. In a UAT-embedded ARPS, the reference stations transmit navigation signals in the ground segment and airborne relays transfer measured information in the automatic dependent surveillance broadcast (ADS-B) segment. To verify the feasibility of ARPS in UAT, we performed various simulations. The simulation results show that the ARPS can be operated in UAT to provide accurate positioning, although the mobility of airborne relays affects the accuracy of system.
27 March 2014 in IEEE Transactions on Wireless Communications
In this paper, we propose a novel dynamic slot-assignment scheme using artificial collisions called artificial collision-based dynamic slot assignment (AC-DSA) for multi-hop networks, which is based on the in-band control mechanism. In-band control-based networks have no exclusively reserved slots for newly arrived nodes; thus, the throughput can be improved compared with that of the out-of-band control-based networks. In in-band control based networks, a newly arrived node can use idle slots to transmit its control packet to request a slot assignment. However, if no idle slots are available, the node cannot transmit its control packet even though it has a higher priority than the existing nodes in the network, because a newly arrived node has to wait until idle slots are available in conventional schemes. To address this issue, AC-DSA uses the duration information of artificial packet collisions as a control message for slot assignment, which enables nodes with high priority to deprive a non-idle slot of nodes with low priority to guarantee quality of service requirements when no idle slots are available. We formulate an analytical model for the proposed slot-assignment scheme and compare it with the conventional one. Further, we demonstrate the feasibility and efficiency of the AC-DSA during high-traffic conditions considering the capture effect.