To date, the lack of age-appropriate medicines for many indications results in dose manipulation of commercially available dosage forms, commonly resulting in inaccurate doses. Various printing technologies have recently been explored in the pharmaceutical field due to the flexible and precise nature of the techniques. The aim of this study was, therefore, to compare the currently used method to produce patient-tailored warfarin doses at HUS Pharmacy in Finland with two innovative printing techniques. Dosage forms of various strengths (0.1, 0.5, 1, and 2 mg) were prepared utilizing semisolid extrusion 3D printing, inkjet printing and the established compounding procedure for oral powders in unit dose sachets (OPSs). Orodispersible films (ODFs) drug-loaded with warfarin were prepared by means of printing using hydroxypropylcellulose as a film-forming agent. The OPSs consisted of commercially available warfarin tablets and lactose monohydrate as a filler. The ODFs resulted in thin and flexible films showing acceptable ODF properties. Moreover, the printed ODFs displayed improved drug content compared to the established OPSs. All dosage forms were found to be stable over the one-month stability study and suitable for administration through a naso-gastric tube, thus, enabling administration to all possible patient groups in a hospital ward. This work demonstrates the potential of utilizing printing technologies for the production of on-demand patient-specific doses and further discusses the advantages and limitations of each method.

Currently, the number of approved veterinary medicines are limited, and human medications are used off-label. These approved human medications are of too high potencies for a cat or a small dog breed. Therefore, there is a dire demand for smaller doses of veterinary medicines. This study aims to investigate the use of three semi-solid extrusion 3D printers in a pharmacy or animal clinic setting for the extemporaneous manufacturing of prednisolone containing orodispersible films for veterinary use. Orodispersible films with adequate content uniformity and acceptance values as defined by the European Pharmacopoeia were produced with one of the studied printers, namely the Allevi 2 bioprinter. Smooth and flexible films with high mechanical strength, neutral pH, and low moisture content were produced with a high correlation between the prepared design and the obtained drug amount, indicating that the Allevi 2 printer could successfully be used to extemporaneously manufacture personalized doses for animals at the point-of-care.

Since the last decade, the polymer-drug conjugate (PDC) approach has emerged as one of the most promising drug-delivery technologies owing to several benefits like circumventing premature drug release, offering controlled and targeted drug delivery, improving the stability, safety, and kinetics of conjugated drugs, and so forth. In recent years, PDC technology has advanced with the objective to further enhance the treatment outcomes by integrating nanotechnology and multifunctional characteristics into these systems. One such development is the ability of PDCs to act as theranostic agents, permitting simultaneous diagnosis and treatment options. Theranostic nanocarriers offer the opportunity to track the distribution of PDCs within the body and help to localize the diseased site. This characteristic is of particular interest, especially among those therapeutic approaches where external stimuli are supposed to be applied for abrupt drug release at the target site for localized delivery to avoid systemic side effects (e.g., Visudyne^®). Thus, with the help of this review article, we are presenting the most recent updates in the domain of PDCs as nanotheranostic agents. Different methodologies utilized to design PDCs along with imaging characteristics and their applicability in a wide range of diseases, have been summarized in this article.

Currently, there are a few or none marketed gabapentin veterinary products, leading to treatment with compounded dosage forms or off-label use of human-marketed products. With the said approaches, there are significant risks of preparation errors, rendering these practices suboptimal. A new manufacturing technique to accurately and rapidly prepare veterinary dosage forms close to the point-of-care is needed. However, a current hurdle in developing small-dose gabapentin dosage forms is the quantification of the gabapentin molecule. UV-Vis spectrophotometric quantification possesses suitable properties for implementation at small production sites, but quantifying gabapentin with the said technique has proven to be challenging as the small molecule lacks chromophores. This study aimed at thoroughly assessing UV-Vis spectrophotometric gabapentin quantification methods with the intent of finding a reliable method. Excellent linearity (R² = 0.9998) in a broad and useful concentration range (0.5-40 µg/mL) was detected for the ascorbic acid derivatization method at a wavelength of 376 nm. The method was successfully applied to determine the drug content in the prepared semi-solid extrusion 3D-printed dosage forms. This study proved that pet-friendly tailored gabapentin dosage forms could easily be manufactured by semi-solid extrusion 3D printing and UV-Vis spectrophotometrically analyzed with the ascorbic acid derivatization method.

Certain patient populations receive insufficient medicinal treatment due to a lack of commercially available products. The number of approved veterinary products is limited, making animals a patient population with suboptimal medicinal treatments available. To answer to this unmet need, compounding and off-label use of human-marketed products are practiced. Both of which have a significant risk of preparation errors. Hence, there is a dire demand to find and implement a more automated approach to the accurate, precise, and rapid production of veterinary dosage forms close to the point-of-care. This study aimed to assess the use of semi-solid extrusion-based 3D printing for the preparation of tailored doses of theophylline in the form of a chewable dosage form suitable for veterinary use. This study proved that semi-solid extrusion-based 3D printing could successfully be utilized to manufacture pet-friendly, chewable theophylline-loaded tablets. The prepared dosage forms showed a high correlation (R² = 0.9973) between the designed size and obtained drug amount and met the USP and Ph. Eur. content uniformity criteria. Furthermore, the stability study showed the dosage form being stable and able to be used for up to three months after printing.

In recent years, polymer-based advanced drug delivery and tissue engineering have grown and expanded steadily. At present, most of the polymeric research has focused on improving existing polymers or developing new biomaterials with tunable properties. Polymers with free functional groups offer the diverse characteristics needed for optimal tissue regeneration and controlled drug delivery. Allyl-terminated polymers, characterized by the presence of a double bond, are a unique class of polymers. These polymers allow the insertion of a broad diversity of architectures and functionalities via different chemical reactions. In this review article, we shed light on various synthesis methodologies utilized for generating allyl-terminated polymers, macromonomers, and polymer precursors, as well as their post-synthesis modifications. In addition, the biomedical applications of these polymers reported in the literature, such as targeted and controlled drug delivery, improvement i aqueous solubility and stability of drugs, tissue engineering, and antimicrobial coatings, are summarized.