Kenji Suzuki

Prof. Kenji Suzuki

Faculty of Education, Niigata University, Niigata, Japan
orcid

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2012 in International Journal of Fatigue
Verified
Journal Article
Closed access
TTTran Hung Tra
Tran Hung Tra
MOMasakazu Okazaki
Masakazu Okazaki
Kenji SuzukiKenji Suzuki
Kenji Suzuki

1 January 2016 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
MMMilton Muzvidziwa
Milton Muzvidziwa
MOMasakazu Okazaki
Masakazu Okazaki
Kenji SuzukiKenji Suzuki
Kenji Suzuki
SHSatoshi Hirano
Satoshi Hirano

1 December 2017 in NDT & E International
Verified
Journal Article
Closed access
Kenji SuzukiKenji Suzuki
Kenji Suzuki

1 December 2015 in International Immunopharmacology
Verified
Journal Article
Closed access
RSRemya Sreedhar
Remya Sreedhar
SASomasundaram Arumugam
Somasundaram Arumugam
VKVengadeshprabhu Karuppagounder
Vengadeshprabhu Karuppagounder
Rajarajan Amirthalingam ThandavarayanRajarajan Amirthalingam Thandavarayan
Rajarajan Amirthalingam Thandavarayan
VGVijayasree Giridharan
Vijayasree Giridharan
KWKenichi Watanabe
Kenichi Watanabe

1 January 2003 in Texture, Stress, and Microstructure
Verified
Journal Article
Open access
PDF file
Kenji SuzukiKenji Suzuki
Kenji Suzuki
KTKeisuke Tanaka
Keisuke Tanaka
High‐energy X‐rays from a synchrotron radiation source, SPring‐8, were applied to the stress measurements of thermal barrier coating (TBC). The specimen had a zirconia top coat on a bond coat of NiCoCrAlY sprayed on the substrate of Ni‐base super alloys. The stress in the bond coat was measured through the top coat using the diffraction of Ni3Al 311 by high‐energy X‐rays with an energy of 72 keV. The sin2ψ method was used to determine the stress value. A specially designed furnace with a wide beryllium window was developed to conduct in-situ measurements of the internal stress in the bond coating at the room temperature, 773, 1073, and 1373 K. The internal stress was tensile at the room temperature, and decreased with increasing temperature. At 1073K or higher, the internal stress in the bond coat was released due to softening of the bond coat. The normal stress perpendicular to the coating surface of TBC was evaluated by a new hybrid method. Since the penetration depth of low‐energy X‐ray is very small around a few micrometers for zirconia, the stress value measured by the sin2ψ method is the in‐plane stress, σ1, and the stress perpendicular to the surface was zero. On the other hand, the penetration depth of high‐energy X‐rays is very deep, so the measured stress value will be the in‐plane stress minus the out‐of‐plane stress, i.e. σ1 − σ3. The normal stress perpendicular to the surface, σ3, i.e. the spalling stress, was estimated from these two measurements. The specimens were exposed in air atmosphere at 1373 K for 500, 1000, and 2000 h. The distribution of the spalling stress in the top coat was estimated by the hybrid method. The spalling stress near the interface to the bond coat changed to a large tension after long‐time exposure.

1 May 2010 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
Kenji SuzukiKenji Suzuki
Kenji Suzuki
TSTakahisa Shobu
Takahisa Shobu
Material of the specimen was austenitic stainless steel (SUS316L). The specimens were given tensile plastic strains from 0% to 55%. The Vickers hardness of the specimen corresponded to the plastic strain. The residual macrostress was measured by Mn-Kα radiations. The residual macrostress of the annealed specimen had a small compression and changed into a tension after ten- sile plastic deformation. The specimen with 1% plastic strain showed the maximum tensile residual stress. To examine the dependency of the residual stress on the lattice plane, the residual microstress for each lattice plane was measured by hard synchrotron X-rays. The residual microstress was related with Young’s modulus which was calculated by Kro¨ ner model. A new method, 2θ-cos2 χ method, was proposed to solve the problem of coarse grains and it was excellent in comparison with the sin2 ψ method.