In the oil and gas industry, the corrosion attributed to hydrogen sulfide (H2S) is one of the most significant challenges. This review paper systematically investigates the diverse facets of H2S corrosion, including its sources, corrosion locations, mechanisms, and resultant corrosion products. Understanding different forms of H2S corrosion, such as stress-oriented hydrogen-induced cracking (SO-HIC), sulfide stress cracking (SSC), and hydrogen-induced cracking (HIC), provides a thorough comprehension of these phenomena. The paper discusses critical factors influencing H2S corrosion, such as temperature, flow rate, pH, and H2S concentration, highlighting their implications for sustainable practices in the oil and gas sector. The review emphasizes the significance of monitoring and mitigation strategies, covering continuous monitoring, applying corrosion inhibitors, selecting materials, and conducting thorough data analysis and reporting. Furthermore, the role of training in fostering a sustainable approach to H2S corrosion management is highlighted. This exploration advances the overarching goal of sustainable development in the oil and gas industries by providing insights into understanding, monitoring, and mitigating H2S corrosion. The findings presented here offer a foundation for developing environmentally conscious strategies and practices to guarantee the long-term viability and flexibility of refinery operations.
This comprehensive review examines the phenomena of stress corrosion cracking (SCC) and chloride-induced stress corrosion cracking (Cl-SCC) in materials commonly used in the oil and gas industry, with a focus on austenitic stainless steels. The study reveals that SCC initiation can occur at temperatures as low as 20 °C, while Cl-SCC propagation rates significantly increase above 60 °C, reaching up to 0.1 mm/day in environments with high chloride concentrations. Experimental methods such as Slow Strain Rate Tests (SSRTs), Small Punch Tests (SPTs), and Constant-Load Tests (CLTs) were employed to quantify the impacts of temperature, chloride concentration, and pH on SCC susceptibility. The results highlight the critical role of these factors in determining the susceptibility of materials to SCC. The review emphasizes the importance of implementing various mitigation strategies to prevent SCC, including the use of corrosion-resistant alloys, protective coatings, cathodic protection, and corrosion inhibitors. Additionally, regular monitoring using advanced sensor technologies capable of detecting early signs of SCC is crucial for preventing the onset of SCC. The study concludes with practical recommendations for enhancing infrastructure resilience through meticulous material selection, comprehensive environmental monitoring, and proactive maintenance strategies, aimed at safeguarding operational integrity and ensuring environmental compliance. The review underscores the significance of considering the interplay between mechanical stresses and corrosive environments in the selection and application of materials in the oil and gas industry. Low pH levels and high temperatures facilitate the rapid progression of SCC, with experimental results indicating that stainless steel forms passive films with more defects under these conditions, reducing corrosion resistance. This interplay highlights the need for a comprehensive understanding of the complex interactions between materials, environments, and mechanical stresses to ensure the long-term integrity of critical infrastructure.
Metakaolinite-based geopolymer binder was prepared at room temperature by mixing calcined claystone and potassium alkaline activator. Various granular inorganic fillers were added, amounting to 65 vol % to form geopolymer composites. The effect of four types of fillers (sand quartz, chamotte, cordierite, and corundum) on the thermo-mechanical properties of metakaolinite-based geopolymer composites were investigated. The samples were also examined by an X-ray diffraction method to determine their phase composition. The pore size distributions were determined by a mercury intrusion porosimeter. The XRD revealed the crystallization of new phase (leucite) after thermal exposure at 1000 °C and higher. Geopolymer binders had low mechanical properties (flexural strength 2.5 MPa and compressive strength 45 MPa) and poor thermo-mechanical properties (especially high shrinkage—total shrinkage 9%) compared to geopolymer composites (flexural strength up to 13.8 MPa, compressive strength up to 95 MPa and total shrinkage up to 1%). The addition of fillers reduced the shrinkage of geopolymers and improved their mechanical properties. The results have shown that the compressive strength tested in situ and after exposure to high temperature are in conflict. Geopolymer composites with the addition of chamotte had the best mechanical properties before and after thermal exposure (compressive strength up to 95 MPa). The average pore size diameters increased with the increasing temperature (from 10 nm to approx. 700 nm). The fillers addition decreased the pore volume (from 250 mm3/g to approx. 100 mm3/g).
A metakaolinite-based geopolymer binder was prepared by using calcined claystone as the main raw material and potassium as the alkaline activator. Chamotte was added (65 vol%) to form geopolymer composites. Potassium hydroxide (KOH) was used to adjust the molar ratio of K/Al and the effect of K/Al on thermo-mechanical properties of geopolymer composites was investigated. This study aimed to analyze the effect of K/Al ratio and exposure to high temperatures (up to 1200 °C) on the compressive and flexural strengths, phase composition, pore size distribution, and thermal dilatation. With an increasing K/Al ratio, the crystallization temperature of the new phases (leucite and kalsilite) decreased. Increasing content of K/Al led to a decline in the onset temperature of the major shrinkage. The average pore size slightly increased with increasing K/Al ratio at laboratory temperature. Mechanical properties of geopolymer composites showed degradation with the increase of the K/Al ratio. The exception was the local maximum at a K/Al ratio equal to one. The results showed that the compressive strength decreases with increasing temperature. For thermal applications above 600 °C, it is better to use samples with lower K/Al ratios (0.55 or 0.70).
The present study focused on investigating the differences in properties between calcined and milled aluminosilicates with different particle size distributions. Two types of clay, i.e., kaolin and kaolinitic claystone, were subjected to calcination at 750 °C, and subsequent milling to obtain different fractions with distinct particle size distributions. These fractions were then combined with a potassium alkaline activator and quartz sand in a 50:50 weight ratio to form a geopolymer composite. The geopolymer binders were then characterized using a mercury intrusion porosimeter (MIP), scanning electron microscopy (SEM), and a rotary rheometer. Mechanical tests were conducted on the geopolymer composites prepared from aluminosilicates with varying particle size distributions. The findings indicated that aluminosilicates with a finer particle size distribution exhibited higher levels of dissolved aluminum (10,000 mg/kg) compared to samples with coarser particle size distributions (1000 mg/kg). Additionally, as the particle size distribution decreased, the dynamic viscosity of the geopolymer binders increased, while the average pore size decreased. Finally, the mechanical properties of the geopolymer composites derived from both tested aluminosilicates demonstrated a decline in performance as the mean particle size increased beyond 10 µm.