The resistance force generated when the locked-wheel acts on the soil is critical for deciding the traveling performance of push–pull locomotion. The resistance force depends on the tangential force of the sliding soil wedge beneath the wheel, and the tangential force depends on the forces of the soil and the wheel perpendicular to the tangential direction. Hence, the normal stress distribution of the locked-wheel can affect the resistance force. Previous studies indicated different insights that describe either a uniform or non-uniform shape of the normal stress distribution. The distribution of the locked-wheel still needs to be examined experimentally. This study measured the normal stress distribution using the wheel sensor system, and the variation of the contact area and slip surface beneath the wheel were also observed in PIV analysis. Those results showed that the normal stress distribution was non-uniform along the wheel contact area, and the change of the distribution was confirmed with the change of the contact area and slip surface. Then, the resistance force calculated by a preliminary model based on the measured data was compared with the total resistance force of the wheel measured by a separate sensor. This comparison provided a theoretical consideration for the measured data.
This paper presents a method of constructing C programs from mainframe assembly programs. IBM mainframe assembly programs, which are called as subroutines from programs written in high-level language such as COBOL, are automatically translated into equivalent C programs. The assembly programs are converted into intermediate representation (IR) of the SSA form on which dataflow analysis, recognition of control structures, and pattern match based transformation are applied to produce codes with readability. Our method features documentation of the translation process. Along with translation, correspondence between the source assembly codes and the resulting C codes are generated as documents, which plays very important role in manually correcting incomplete C codes from architecture dependent codes or self morphing codes. Furthermore, comments in the assembly programs are embedded into appropriate positions in the resulting C programs. A prototype system based on our method successfully translated some assembly codes into C program with function, if, and do-while structures.
Planetary exploration rovers have required a high traveling performance to overcome obstacles such as loose soil and rocks. Push-pull locomotion rovers is a unique scheme, like an inchworm, and it has high traveling performance on loose soil. Push-pull locomotion uses the resistance force by keeping a locked-wheel related to the ground, whereas the conventional rotational traveling uses the shear force from loose soil. The locked-wheel is a key factor for traveling in the push-pull scheme. Understanding the sinking behavior and its resistance force is useful information for estimating the rover’s performance. Previous studies have reported the soil motion under the locked-wheel, the traction, and the traveling behavior of the rover. These studies were, however, limited to the investigation of the resistance force and amount of sinkage for the particular condition depending on the rover. Additionally, the locked-wheel sinks into the soil until it obtains the required force for supporting the other wheels’ motion. How the amount of sinkage and resistance forces are generated at different wheel sizes and mass of an individual wheel has remained unclear, and its estimation method hasn’t existed. This study, therefore, addresses the relationship between the sinkage and its resistance force, and we analyze and consider this relationship via the towing experiment and theoretical consideration. The results revealed that the sinkage reached a steady-state value and depended on the contact area and mass of each wheel, and the maximum resistance force also depends on this sinkage. Additionally, the estimation model did not capture the same trend as the experimental results when the wheel width changed, whereas, the model captured a relatively the same trend as the experimental result when the wheel mass and diameter changed.
For push–pull locomotion, it has been confirmed by this research group that the support force of the wheels is enhanced by performing the sinking operation to provide support force. However, the sinking operation is an additional operation used for the rover to travel. Ideally, if the rover can operate without sinking, travel efficiency is improved. On the other hand, flexible wheels are often used for the rover. Due to stress dispersion, these wheels are less likely to damage the ground. Therefore, it would be beneficial if the use of these wheels could improve the travel ability of the push–pull motion. In this study, we focused on whether the use of flexible wheels can avoid subsidence and tested their performance through different parameters.
1 January 2023 in The Proceedings of the Dynamics & Design Conference
This paper presents time-suboptimal vibration-free reference trajectories for positioning 1-DOF undamped linear oscillatory systems. The reference trajectory is firstly parameterized in time-domain and then the parameter values are determined to satisfy constraints in both time and frequency domains. One of the frequency domain constraints guarantees the robust-performance of vibration mitigation against variation of natural mode. Time-optimal problems are partly solved under given rated values of the acceleration and the velocity. While analytical solutions are available in the undamped case, the numerical solution is also valuable since it gives another referece trajectory of shorter positioning time. As a result, the deterioration of position time is minimized and the difference from the so-called time-optimal trajectory is kept small. The positioning time is also comparable to the well-known UM-ZV (Unity-Magnitude Zero-Vibration) shaped one and the variant. The proposed vibration-free reference trajectories are used in a real linear positioning system and the performance is verified in experiments as well as numerical simulations.