Over the past decade, halide perovskite systems have captured widespread attention among researchers since their exceptional photovoltaic (PV) performance is disclosed. The unique combination of optoelectronic properties and solution processability shown by these materials has enabled perovskite solar cells (PSCs) to reach efficiencies higher than 25% at low fabrication costs. Moreover, PSCs display enormous potential for modern unconventional PV applications, since they can be made lightweight, semitransparent (ST), and/or flexible by means of appropriate design strategies. In particular, by enabling transparency and high efficiency simultaneously, ST‐PSCs hold great promise for future versatile utilization in the context of building‐integrated PVs (BIPVs) or as top cells to be coupled with conventional lower‐bandgap bottom cells in tandem PV devices. The present review aims to provide a detailed overview of latest research about ST‐PSCs for BIPVs and tandems, by critically reporting on the most updated and effective design strategies in view of these two possible future applications. The differences and similarities between the available approaches are punctually highlighted, emphasizing the importance of a rigorous application‐orientated ST‐PSC design. Finally, the main challenges and issues about device design, operation, and stability that need to be addressed before commercialization are thoroughly scanned.

The perovskite film is the core of a perovskite solar cell (PSC), and its quality is crucial for the performance of such devices. The morphology, crystallinity, and surface coverage of the perovskite layer greatly affect the power conversion efficiency (PCE), hysteresis, and long-term stability of PSCs. The incorporation of appropriate solvent additives in the perovskite precursor solution is an effective strategy to control the film morphology and reduce the defects and grain boundaries. However, the commonly used solvent additives are environmentally harmful and highly toxic. In this work, α-terpineol (a nontoxic, eco-friendly, and low-cost monoterpene alcohol) is employed for the first time as an alternative green solvent additive to improve the quality of one-step solution-processed CH₃NH₃PbI_3–xCl_x films and to restrain nonradiative recombination in the corresponding devices. An in-depth investigation of the physicochemical effects induced by such a high-boiling-point, polar protic solvent when incorporated into a conventional perovskite solvent system is provided. The collected data demonstrate that the addition of a precise amount of α-terpineol can generate uniform and highly crystalline perovskite films with improved photovoltaic performances. Through this approach, the PCE of planar n–i–p PSCs is boosted up to 17.5% (against 16.1% of the top control device) with reduced hysteresis and enhanced ambient stability.

Organic Photovoltaics (OPVs) based on Bulk Heterojunction (BHJ) blends are a mature technology. Having started their intensive development two decades ago, their low cost, processability and flexibility rapidly funneled the interest of the scientific community, searching for new solutions to expand solar photovoltaics market and promote sustainable development. However, their robust implementation is hampered by some issues, concerning the choice of the donor/acceptor materials, the device thermal/photo-stability, and, last but not least, their morphology. Indeed, the morphological profile of BHJs has a strong impact over charge generation, collection, and recombination processes; control over nano/microstructural morphology would be desirable, aiming at finely tuning the device performance and overcoming those previously mentioned critical issues. The employ of compatibilizers has emerged as a promising, economically sustainable, and widely applicable approach for the donor/acceptor interface (D/A-I) optimization. Thus, improvements in the global performance of the devices can be achieved without making use of more complex architectures. Even though several materials have been deeply documented and reported as effective compatibilizing agents, scientific reports are quite fragmentary. Here we would like to offer a panoramic overview of the literature on compatibilizers, focusing on the progression documented in the last decade.

The design of multifunctional nanostructured materials is the key to the development of smart wearable devices. For instance, nanostructures endowed with both piezoelectric and photocatalytic activities could well be the workhorse for solar-light-driven self-cleaning wearable sensors. In this work, a simple strategy for the assembly of a flexible, semitransparent piezophotocatalytic system is demonstrated by leveraging rational wet chemistry synthesis of ZnO-based nanosheets/nanoflowers (NSs/NFs) under basic pH conditions onto flexible ITO/PET supports. A KMnO₄ pretreatment before the ZnO synthesis (seeded ZnO) allows for the control of the density, size, and orientation of the NSs/NFs systems compared to the systems produced in the absence of seeding (seedless ZnO). The electrical response of the sensors is extracted at a 1 V bias as a function of bending in the interval between 0 and 90°, being the responsivity toward bending significantly enhanced by the KMnO₄ treatment effect. The photocatalytic activity of the sensors is analyzed in aqueous solution (methylene blue, 25 μM) by a solar simulator, resulting in similar values between seedless and seeded ZnO. Upon bending the sensor, the photocatalytic activity of seedless ZnO is almost unaffected, whereas that of seeded ZnO is improved by about 25%. The sensor's reusability and repeatability are tested in up to three different cycles. These results open up the way toward the seamless integration of bending sensitivity and photocatalysis into a single device.

In this paper, we developed different three-component organic heterojunction structures supported by PET/ITO substrates with the aim to study the possible synergies and/or compromises between charge transfer (CT) and energy transfer (ET) processes in organic solar cells (OSCs). As components, we employed poly(3-hexylthiophene-2,5-diyl) (P3HT; donor), [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM; acceptor) and poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT) that is known to give good ET to P3HT. At first, we observed that in a planar heterojunction (PHJ) solar cell, F8BT has to be properly located in between P3HT and PCBM to get a cascade energy level configuration allowing for a better CT and power conversion efficiency. Then, we observed that by producing a P3HT:F8BT blend, the energy transfer process can be improved in the P3HT:F8BT/PCBM active layer. This may enable decreasing the thickness of the active layer while maintaining a similar PCE that is very interesting for the development of transparent OSCs. However, the P3HT:F8BT blend limits the P3HT–PCBM CT with respect to a P3HT/F8BT/PCBM PHJ, showing that a compromise between CT and ET is needed to get a higher PCE or higher transparency. By the above approach, in this paper, we developed highly transparent heterojunction structures for solar cell devices with PCEs comparable to those observed from the colorful reference P3HT/PCBM PHJ solar cells on PET/ITO substrates.