The development of green synthesis methods for supported noble metal catalysts remains important challenges to improve their sustainability. Here we first synthesized carbon-supported Pd catalysts in a green Leidenfrost droplet reactor without reducing agents, high-temperature calcination and reduction procedures. When the aqueous solution containing Pd nitrate precursor, carbon support, and water is dripped on a hot plate, vapor layer is formed between a solution droplet and hot surface, which allow the solution droplet to be levitated on the hot surface (Leidenfrost phenomena). Subsequently, Pd nanoparticles can be prepared without reducing agents in a weakly basic droplet reactor created by the Leidenfrost phenomena, and then the as-prepared Pd nanoparticles are loaded on carbon supports during boiling down the droplet on hot surface. Compared to conventional incipient wetness and chemical synthetic methods, the Leidenfrost droplet reactor does not need energy-consuming, time-consuming, and environmentally unfriendly procedures, which leads to much shorter synthesis time, lower carbon dioxide emission, and more ecofriendly process in comparison with conventional synthesis methods. Moreover, the catalysts synthesized in the Leidenfrost droplet reactor provided much better catalytic activity for room-temperature formic acid decomposition than those prepared by the incipient wetness method.
The purpose of this study was to investigate and compare the influence of torrefaction and an ashless process on the physical and chemical properties of pitch pine sawdust (PSD) and kenaf as types of woody and herbaceous biomass. The physicochemical properties of the materials pretreated by the ashless process with torrefaction including proximate and ultimate analysis, hydrophobicity, grindability, morphology, and structure were analyzed. The results showed that when ashless Kenaf was torrefied, the high heating rate and atomic ratios of O/C and H/C increased. The tendency of the torrefied, ashless Kenaf to absorb water decreased, and it became more hydrophobic (approximately 0% for the uptake rate of moisture). In addition, the grindability of the torrefied, ashless Kenaf was substantially improved compared to that of pretreated PSD. Brunauer–Emmett–Teller and scanning electron microscopy results showed that when Kenaf was pretreated, particles easily lost their fibrous structure and cracked as the number of macropores decreased. These results indicate that the herbaceous biomass of Kenaf, when pretreated with both torrefaction and the ashless process, exhibits improved physicochemical properties compared to the woody PSD.
Biomass is a solid fuel that can be used instead of coal to address the issue of greenhouse gases. Currently, biomass is used directly in combustion or via co-combustion in coal-fired power plants. However, its use is limited due to calorific value and ash problems. In this study, wet torrefaction (WT) was carried out at various temperatures (160 °C, 180 °C, and 200 °C) and the properties of the product were evaluated. In comparison to dry torrefaction, the ash contained in biomass was extracted by an acidic solution (i.e., acetic acid) from the overreaction of the biomass. From examining the ash content of the treated WT, it was confirmed that K2O of basic ash was mainly extracted. In particular, in the case of K2O, since the main cause of combustion problems are issues such as fouling and slagging, the removed WT can be stably combusted in the boiler. Finally, the combustion and emission behaviors were evaluated by TGA-DTG and TGA-FTIR. As the fuel-N was decreased in the WT proess, the NOx in the emission gas after combustion was lower than that of raw miscanthus, and SO2 showed a similar value. As a result, it was confirmed that the WT sample is an advanced fuel in terms of fuel upgrading, alkali minerals, and NOx emission compared to raw miscanthus.
Developing effective, economical, and environmentally sound approaches for sewage sludge management remains an important global issue. In this paper, we propose a bioethanol-lignin (nonfood biomass)-based sewage sludge upgrading process for enhancing the heating value and reducing air pollutants of hybrid sewage sludge fuel (HSF) for the effective management of sewage sludge. Sewage sludge paste with the lignin-CaO solution implies drying at 105 °C accompanied by torrefaction at 250 °C. During torrefaction, moisture and partly volatile matter begin to evaporate, and are almost vaporized out to the surface. In this study, the proposed process enhances the net caloric value (NCV) to 37%. The lignin-embedded HSF shows a two-in-one combustion peak regardless of the mixing ratio, resulting in a 70% reduction of unburned carbon (UBC) emissions, which is one of the particular matter (PM) sources of combustion flue gas. Other air pollutants, such as CO, hydrocarbon, NOx, and SOx, were also reduced by the proposed process. In particular, SOx emission remained at ~1 ppm (average value) regardless of the sulfur content of the fuel.
15 September 2023 in ACS Sustainable Chemistry & Engineering