In this paper, to our best knowledge, it is the first time to present a precise simulation and detailed design of angular correlated color temperature (CCT) distribution of white LEDs covering a range of CCT from 2800K to 6500K. An optimized design of packaging structure with a silicone lens covering a phosphor dome performed an extreme small angular CCT deviation of 105K in the simulation and 182K in a corresponding real sample for a white LED with the CCT near 6500K.

In this paper, as to our best knowledge, we propose and demonstrate the first precise phosphor modeling scheme to simulate the chromatic performance of white LEDs with silicate phosphors. The phosphor model is useful to accurately simulate the power ratio of the blue and yellow lights emitted by the white LEDs and is important in white LED package.

In this paper, a metal layer assisted guide mode resonance (MaGMR) device with high sensitivity is proposed for bioanalytical applications and its functioning is experimentally proved. We find that the reflection spectra present a unique inversed response. The resonance mechanism is also discussed. Numerical calculation results indicate that the high sensitivity performance of MaGMR comes from the strongly asymmetric resonance modal profile and low propagation angle inside the waveguide. There is a one-fold enhancement of the evanescent wave in the analytes region compared to typical GMR. According to the experimental results, the proposed MaGMR achieved a bulk sensitivity of 376.78nm/RIU in fundamental TM mode resonating at 0.809μm with the first diffraction angle. Experiment results show a 264.78% enhancement in the sensitivity compared to that of the typical GMR sensor in the same resonance conditions of TM mode.

In this paper, we start from the study on the packaging efficiency of the phosphor-converted white LED via a new way to measure and calculate the blue light from the blue die to the encapsulation lens. Then we try to estimate the limit of luminous efficacy of a pcW-LED with Type VII structure. In the calculation, with the EQE of 81% of the blue die and Stokes loss, we obtain the optimal limit of luminous efficacy. The largest one reaches 300 lm/W, and occurs for green-white light with CCT from 4000K to 5000K. More practical limit is calculated in considering phosphor quantum loss and geometry loss, and the practical limit of luminous for CRI around 60 is around 210 lm/W, and for CRI larger than 80 is around 175 lm/W. Luminous efficacy will be sacrificed to obtain higher CRI. In order to know the real optical flux on the illuminated target, we introduce the optical utilization factor (OUF). Three application cases are discussed. The OUFs for light bulb, automotive head lamp, and street light are 90%, 60% and 45%, respectively. In considering human factors, it is interesting to find that a light source with lower luminous efficacy can perform higher illumination luminous efficacy (ILE). Therefore it is important to use ILE rather than LE when a light source is practically applied to lighting.

Street lighting, which is one of the main players in energy waste and light pollution at night, still faces the challenge of efficient lighting of roadways with curved and twisted shapes. To meet this challenge, we propose an effective and efficient adaptive light-emitting diode (LED) luminaire. This LED lamp delivers a roadway-shape light pattern, which maximizes illumination performance. The light is efficiently and homogeneously directed only where is needed; which reduces glare, and improves both the eye comfort and the visual discrimination ability of car drivers and pedestrians. The proposed luminaire is very practical in that it only requires to replace the cover plate, which is a special microlens array sheet, to produce different shape light patterns. The adaptive mechanism is simple and effective: LED light is first collimated and then efficiently distributed on a freeform roadway by the special microlens sheet. We present an extensive analysis of the lighting adaptability of the proposed luminaire by Monte Carlo ray tracing. In particular, we studied the effect of the main microlens structural parameters in the shape and size of the delivered illumination distribution on the roadway. We present a design example, a prototype construction, and an experimental confirmation on a scale street lighting system. Simulations and experimental results show the advantages of adaptive luminaires over the traditional nonadaptive approaches.

Phosphor-converted white light-emitting diodes (pc-WLEDs) have become a major light source in general lighting. To stabilize the photometric characteristics of pc-WLEDs, much effort has been made to manage the heat dissipation of the LED dies. The thermal problems of the phosphor parts, a critical reliability concern for pc-WLEDs, have recently attracted academic interest. This study proposed a practical approach for measuring phosphor temperature in an operating pc-WLED using a noncontact, instant detection method to remotely monitor the emission spectrum. Conventionally, an infrared camera or thermocouples have been used to measure temperature. An IR camera requires good calibration on the emissivity and is usually blocked by the lens or other components covered on the phosphors. Moreover, a thermocouple requires time to reach the thermal equivalence between the detector and the sample under testing, and this approach is destructive when used for inner detection. Our approach has advantages over the conventional methods because it is noninvasive, noncontact, and instant, and inner detection. The approach is also independent of the peak wavelength of pumping lights, the concentration and thickness of phosphor, and correlated color temperatures.