CO2 capture by CaO in molten salts is a variant of calcium looping in which the active substances (CaO/CaCO3) are dissolved or in a slurry with inorganic molten salts. One of the main advantages is the nonexistence of degradation in the reactivity between the active material and CO2. Previous research has revealed good absorption and desorption characteristics with CaO contents up to 20 wt% in eutectic CaF2-CaCl2. The hypothesis is that the formed CaCO3 continuously dissolves in the melt, leaving highly reactive CaO readily available for the incoming CO2. In the present study, the CaO content is increased to 40 wt%, and the absorption characteristics is investigated with focus on the sorption capacity and CO2 removal rate. The chemical system is also evaluated experimentally with regards to viscosity and solubility of the formed CaCO3 during CO2 absorption, with the aim of determining chemical upscaling limitations. The results show that the practical CaO content limit is 30 wt%, in which a sorption capacity of 20 g CO2/100 g sorbent is observed, without any deterioration of the reaction kinetics. For 40 wt% CaO, the sorption capacity is higher, but on the expense of the CO2 removal rate and CaO conversion. This is attributed to a significant increase in viscosity and the solubility limit of CaCO3 being exceeded.
A tubular electrostatic precipitator (ESP) was designed and tested for collection of pyrolysis oil in molten salt pyrolysis of milled beech wood (0.5-2 mm). The voltage-current (V-I) characteristics were studied, showing most stable performance of the ESP when N2 was utilized as inert gas. The pyrolysis experiments were carried out in FLiNaK and (LiNaK)2CO3 over the temperature range of 450-600 ℃. The highest yields of pyrolysis oil were achieved in FLiNaK, with a maximum of 34.2 wt% at 500 ℃, followed by a decrease with increasing reactor temperature. The temperature had nearly no effect on the oil yield for pyrolysis in (LiNaK)2CO3 (19.0-22.5 wt%). Possible hydration reactions and formation of HF gas during FLiNaK pyrolysis were investigated by simulations (HSC Chemistry software) and measurements of the outlet gas (FTIR), but no significant amounts of HF were detected.
With the higher penetration of intermittent renewable energy sources in the electric power grid, more flexibility is needed to cope with challenges related to stability and reliability. Consumers can be part of the solution through demand response, for example, by investing in residential batteries that can charge and discharge based on price signals (implicit flexibility) or externally controlled based on grid-related needs (explicit flexibility). In this study, we investigate the feasibility of deploying residential batteries through a case study consisting of 20 households located in south-eastern Norway. The potential annual savings from implicit flexibility are optimized based on the retail electricity price, a power-based tariff, and potential revenues by selling electricity to the grid. Real historical price and consumption data with hourly resolutions from the entire year of 2022 are used as input for the optimization, yielding a theoretical profit potential. Based on this, profitability analyses are performed. The results show that the battery investments will not reach an economic break-even point during their lifetime under today’s electricity price conditions. However, future developments in profit increase from implicit flexibility, substantial investment support, or additional revenues from emerging flexibility markets could make the investment economically attractive for a regular consumer.
The decarbonization of the power sector involves electrification and a massive deployment of variable renewable energy sources, leading to an increase of local transmission congestion and ramping challenges. A possible solution to secure grid stability is local flexibility markets, in which prosumers can offer demand-side flexibility to the distribution system operator or other flexibility buyers through an aggregator. The purpose of this study was to develop a framework for estimating and offering short-term demand-side flexibility to a flexibility marketplace, with the main focus being baseline estimation and bid generation. The baseline is estimated based on forecasts that have been corrected for effects from earlier flexibility activations and potential planned use of internal flexibility. Available flexibility volumes are then estimated based on the baseline, physical properties of the flexibility asset and agreed constraints for baseline deviation. The estimated available flexibility is further formatted into a bid that may be offered to a flexibility marketplace, where buyers can buy and activate the offered flexibility, in whole or by parts. To illustrate and verify the proposed methodology, it was applied to a grocery warehouse. Based on real flexibility constraints, historic meter values, and forecasts for this use-case, we simulated a process where the flexibility is offered to a hypothetic flexibility marketplace through an aggregator.