Lithium ion (Li-Ion) and lithium polymer (Li-Po) batteries need to be used within certain voltage/current limits. Failure to observe these limits may result in damage to the battery. In this work, we propose a low voltage battery management system (LV-BMS) that balances the processes of the battery cells in the battery pack and the activating-deactivating of cells by guaranteeing that the operation is within these limits. The system operates autonomously and provides energy from the internal battery. It has a modular structure and the software is designed to control the charging and discharging of eight battery cells at most. A STM32F103 microcontroller is used for system control. The fuzzy logic controller (FLC) is used to set the discharge voltage limit to prevent damage to the battery cells, shorten the settlement time and create a specialized design for charge control. The proposed structure enables solar panel or power supplies with different voltage values between 5 V and 8 V to be used for charging. The experimental results show there was a 42% increase in usage time and the voltage difference between the batteries was limited to a maximum of 65 mV. Moreover, the charge current settles at about 20 ms, which is a much faster response when compared to a PID controller.
The lithium ion type battery has become commercially more popular than the traditional battery and the usage market has increased. The main reason for this expansion and increase is that it has a high voltage value and a high energy density in a single cell. In addition to having these advantages, lithium ion batteries have usage limits. These limits are values such as operating voltage values, continuous current values, operating temperature. The use of battery cells outside the limits of use can shorten the life of the battery cells, leading to undesirable problems such as fire and explosion. These limits must be observed on the BMS and the operation of the battery cells within the safe limits must be guaranteed by the BMS. The proposed study includes a module design for battery management system that allows cell-based opening and closing of the battery pack and allows charging of the cells during use. The components have been chosen for low power consumption. The proposed structure is designed together with the charging unit. Power of module has been provided from its own battery cells. With the designed module and software, a battery pack with 8 battery cells can be created. Serial connected modules communicate with each other and can communicate with the user via serial communication if battery cell information is requested. It also decides on the charging of the series connected cells after the data received from all the modules. As a result of the tests made, it was seen that this module, which was created for the use of modular structures in BMS systems, increased the usage time of the battery pack. In addition, the low voltage level required for charging makes it possible to use many sources, from mobile phone adapters to solar energy, as a charging source.
31 October 2023 in AEU - International Journal of Electronics and Communications
Devre ve kullanılan elemanların boyutlarını küçültmek, çıkış gerilimi dalgalılık ve darbe genlik modülasyonu doluluk oranını azaltmak için literatürde paralel yapıdaki yükseltici tip güç dönüştürücüsü önerilmiştir. Bu yapının yüklü ve yüksüz durumda kararlı çıkış sağlayabilmesi için çeşitli kontrol metotları uygulanmış ve performansları deneysel ortamda karşılaştırılmıştır. Tasarlanan sistem, integral, oransal-integral, bulanık mantık kontrol metotlarının uygulandığı gerçek zamanlı mikro denetleyici temelli bir geri besleme yapısı içermektedir. Elde edilen sonuçlara göre bulanık mantık denetleyicili sistemin tepki süresi diğer yöntemlere göre daha düşük olduğundan dolayı güç verilen sistem için daha kararlı bir güç kaynağı olmaktadır.
30 June 2022 in Mühendislik Bilimleri ve Tasarım Dergisi
GaN FET anahtarlar ufak paket boyutlarına sahip olması ve yüksek çalışma gerilim-akım değerlerini yüksek anahtarlama frekanslarında sağlayabilmesinden dolayı güç elektroniği çeviricilerinde yeni ufuklar açmıştır. Bu çalışma EPC firması tarafından üretilmiş olan küçük paket boyutlarındaki EPC2215 (VDS=200V, ID=32A, RDS(on)=8m) GaN FET anahtarların sonlu elemanlar yöntemi tabanlı ısıl modelinin elde edilmesini ile ilgilidir. JEDEC standartlarınca belirlenen deney talimatları kurulan benzetim modeline uygulanmıştır. Anahtarın jonksiyondan kılıfa, jonksiyondan dış ortama ve jonksiyondan devre kartına olan ısıl dirençleri benzetim modeli ile hesaplanmış ve firmanın veri föylerinde paylaştığı ısıl direnç değerleri ile karşılaştırılmıştır. Daha sonra yine aynı firmaya ait olan, EPC2215 anahtarları ile yapılan, EPC9099 yarım-köprü geliştirme kartının ısıl modellemesi yapılmıştır. Firma tarafından veri föyünde paylaşılan kayıp güç değerleri benzetim modeline uygulanmıştır. Benzetim sonucunda geliştirme kartının ısıl yönden zorlandığı bölgeler belirlenmiştir. Daha sonra benzetim ile elde edilen ısıl dağılım sonuçları ile deneysel termal kamera görüntüleri karşılaştırılmıştır.