Bartosz Powałka

Prof. Bartosz Powałka

orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2016 in Precision Engineering
Verified
Journal Article
Closed access
MSMichał Szydłowski
Michał Szydłowski
BPBartosz Powałka
Bartosz Powałka
Marcin MatuszakMarcin Matuszak
Marcin Matuszak
PKPaweł Kochmański
Paweł Kochmański

1 February 2007 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Closed access
JDJaspreet Singh Dhupia
Jaspreet Singh Dhupia
BPBartosz Powałka
Bartosz Powałka
RKReuven Katz
Reuven Katz
AUA. Galip Ulsoy
A. Galip Ulsoy

18 April 2012 in Journal of Vibration and Control
Verified
Journal Article
Closed access
APArkadiusz Parus
Arkadiusz Parus
BPBartosz Powałka
Bartosz Powałka
KMKrzysztof Marchelek
Krzysztof Marchelek
Stefan DomekStefan Domek
Stefan Domek
MHMarcin Hoffmann
Marcin Hoffmann
During milling of flexible workpieces a regenerative chatter vibration may become a critical factor that limits productivity. It is shown in this paper that a selection of cutting parameters based on a stability lobes diagram may not always be a remedy for low productivity due to increased forced vibration level. Additionally, other factors such as tool wear may limit the selection of stable spindle speeds. This paper presents an active control system that counteracts the development of chatter vibration. The proposed active control system employs Linear Quadratic Gaussian (LQG) algorithm and piezoelectric actuator to suppress vibration during cutting. The Kalman filter is used to estimate the state of the system required by LQG algorithm. The active control introduces damping into the system, thereby raising the critical depth of cut and reducing forced vibration amplitude. It enables stable cutting under a much wider range of cutting parameters than for the uncontrolled system. Cutting tests are performed to demonstrate an effectiveness of the control system. Practical issues limiting applications of the proposed technique are discussed.

17 April 2007 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
JDJaspreet Singh Dhupia
Jaspreet Singh Dhupia
BPBartosz Powałka
Bartosz Powałka
AUA. Galip Ulsoy
A. Galip Ulsoy
RKReuven Katz
Reuven Katz
This paper presents the effect of experimentally evaluated nonlinearities in a machine joint on the overall machine tool dynamic performance using frequency response functions and stability lobe diagrams. Typical machine joints are very stiff and have weak nonlinearities. The experimental evaluation of the nonlinear joint parameters of a commercial translational guide has been discussed in Dhupia et al., 2007, J. Vibr. Control, accepted. Those results are used in the current paper to represent the connection between the column and the spindle of an idealized column-spindle machine structure. The goal is to isolate and understand the effects of such joints on the machine tool dynamic performance. The nonlinear receptance coupling approach is used to evaluate the frequency response function, which is then used to evaluate the stability lobe diagrams for an idealized machine structure. Despite the weak nonlinearities in the joint, significant shifts in the natural frequency and amplitudes at resonance can be observed at different forcing amplitudes. These changes in the structural dynamics, in turn, can lead to significant changes in the location of chatter stability lobes with respect to spindle speed. These variations in frequency response function and stability lobe diagram of machine tools due to nonlinearities in the structure are qualitatively verified by conducting impact hammer tests at different force amplitudes on a machine tool.

1 May 2015 in CIRP Journal of Manufacturing Science and Technology
Verified
Journal Article
Closed access
BPBartosz Powałka
Bartosz Powałka
KJKrzysztof Jemielniak
Krzysztof Jemielniak

13 December 2011 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MSMichał Szydłowski
Michał Szydłowski
BPBartosz Powałka
Bartosz Powałka
Production of precise high-value mechanical elements requires a hundred percent on-site control. Chatter may occur due to random events. Although an unaided human eye can also easily identify the presence of chatter marks, it is economically ineffective. Therefore, an algorithm based on machine vision signals was proposed for surface inspection. The algorithm was designed to build an error map of the examined surface and highlight the regions of probable imperfections. The algorithm is based on local gradient estimation, applied in respect to milling parameters. Estimated local gradient directions are used to calculate the ridge/valley orientations of the machined surface. The local ridge orientation is used for the purpose of computing the surface error map. An experiment was made to test the algorithm. Milled surfaces in both chatter-free and chatter-rich conditions have been analysed with the presented method.