Canopy height is one of the strongest predictors of biomass and carbon in forested ecosystems. Additionally, mangrove ecosystems represent one of the most concentrated carbon reservoirs that are rapidly degrading as a result of deforestation, development, and hydrologic manipulation. Therefore, the accuracy of Canopy Height Models (CHM) over mangrove forest can provide crucial information for monitoring and verification protocols. We compared four CHMs derived from independent remotely sensed imagery and identified potential errors and bias between measurement types. CHMs were derived from three spaceborne datasets; Very-High Resolution (VHR) stereophotogrammetry, TerraSAR-X add-on for Digital Elevation Measurement, and Shuttle Radar Topography Mission (TanDEM-X), and lidar data which was acquired from an airborne platform. Each dataset exhibited different error characteristics that were related to spatial resolution, sensitivities of the sensors, and reference frames. Canopies over 10 m were accurately predicted by all CHMs while the distributions of canopy height were best predicted by the VHR CHM. Depending on the guidelines and strategies needed for monitoring and verification activities, coarse resolution CHMs could be used to track canopy height at regional and global scales with finer resolution imagery used to validate and monitor critical areas undergoing rapid changes.

Mangrove forests are important natural ecosystems due to their ability to capture and store large amounts of carbon. Forest structural parameters, such as canopy height and above-ground biomass (AGB), provide a good measure for monitoring temporal changes in carbon content. The protected coastal mangrove forest of the Everglades National Park (ENP) provides an ideal location for studying these processes, as harmful human activities are minimal. We estimated mangrove canopy height and AGB in the ENP using Airborne LiDAR/Laser (ALS) and TanDEM-X (TDX) datasets acquired between 2011 and 2013. Analysis of both datasets revealed that mangrove canopy height can reach up to ~25 m and AGB can reach up to ~250 Mg•ha−1. In general, mangroves ranging from 9 m to 12 m in stature dominate the forest canopy. The comparison of ALS and TDX canopy height observations yielded an R2 = 0.85 and Root Mean Square Error (RMSE) = 1.96 m. Compared to a previous study based on data acquired during 2000–2004, our analysis shows an increase in mangrove stature and AGB, suggesting that ENP mangrove forests are continuing to accumulate biomass. Our results suggest that ENP mangrove forests have managed to recover from natural disturbances, such as Hurricane Wilma.

Radio Frequency Interference (RFI) is a growing problem in Synthetic Aperture Radar (SAR) systems as scientific motivations push the radars to lower frequencies and as more wireless services share the frequency spectrum. New, advanced SAR instruments, such as NASA’s EcoSAR, DBSAR and DLR’s Tandem-L mission, employ a multichannel architecture capable of Digital Beamforming (DBF). Radars with DBF are capable of notching the antenna pattern in specific directions, which can be utilized to suppress RFI on board or in post-processing. A well-researched beamformer for this purpose is the Minimum Variance Distortionless Response (MVDR) Beamformer. However, the number of interferers that can be removed through notching is limited by the number of receive channels. It is therefore essential to adaptively change the antenna pattern notching throughout the image in time and frequency for the best results with a given number of receive channels. In this paper, we present several methods to achieve this notching by making use of the spatial SAR signal distribution in range time, range frequency, azimuth time and azimuth Doppler that is inherent to the SAR imaging geometry. Because this distribution is time-variable and yet predictable, it can be used to improve the angle of arrival estimation of the RFI and the adaptive notching. The presented methods can be applied to a Digital Beamforming (DBF) SAR signal with multiple channels in elevation and/or in azimuth. Simulations show that the proposed methods increase the ability to notch out-of-swath interference from multiple directions and lessen the impact on in-swath interference. The improvement of the interferometric coherence for a single-pass interferogram acquired by NASA’s EcoSAR system (capable of DBF in elevation) is demonstrated. The removal of periodic RFI artifacts is achieved.

We generated a large-scale mangrove forest height map using multiple TanDEM-X (TDX) interferometric synthetic aperture radar (InSAR) acquisitions with various spatial baselines in order to improve the height estimation accuracy across a wide range of forest heights. The forest height inversion using InSAR data is strongly dependent upon the vertical wavenumber (i.e., perpendicular baseline). First, we investigated the role of the vertical wavenumber in forest height inversion from InSAR data using the sensitivity of the interferometric (volume) coherence to forest height. We used corrected but lower resolution and accuracy Shuttle Radar Topography Mission (SRTM) mangrove height maps as a priori information over Akanda and Pongara National Parks in Gabon to estimate lower and upper boundaries of the vertical wavenumber over test sites from the measured coherence-to-height sensitivity. Only TDX acquisitions within the boundaries of the vertical wavenumber were selected and combined for multibaseline mangrove height inversion. Mangrove forest height was obtained with multibaseline TDX acquisitions and was validated against the reference height derived from field measurement data providing improvements in multibaseline inversion over existing height estimates (i.e., SRTM height) and single-baseline inversions (multibaseline inversion: $r^{2}= {\text{0.98}}$, root mean square error (RMSE) of 2.73 m; SRTM height: $r^{2}= {\text{0.86}}$, ${\text{RMSE}}= {\text{7.21}}$ m; single-baseline inversions: $r^{2}= {\text{0.08}}{\hbox{-}} {\text{0.97}}$, ${\text{RMSE}}= {\text{3.86}}$–11.10 m). As a result, to accurately estimate forest heights over a wide range (3–60 m), multibaseline InSAR acquisitions (at least three different baselines) are needed to exclude biases associated with the vertical wavenumber in forest height inversion.

The high penetration of P-band signals (300–600 MHz) into dense vegetation and the higher temporal stability at low frequencies are key advantages for the estimation of forest properties using synthetic aperture radar (SAR). However, existing services at those frequencies make P-band SAR imagers more vulnerable to the radio frequency interference (RFI). In this paper, a method to detect and geolocate the RFI using digital beamforming (DBF) is presented. The method is implemented using NASA's EcoSAR measurements. This P-band multichannel radar uses a sniffing pulse interleaved during the DBF SAR operation to sense the RFI. RFI detection is implemented with time-bandpass filters while DBF is used to estimate the angle-of-arrival and geolocate the interference. The method is demonstrated for an interferer how EcoSAR could be used to assess the RFI threats to spaceborne missions.