Rubaiyet Haque

Dr. Rubaiyet Haque

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 October 2015 in Flexible and Printed Electronics
Verified
Journal Article
Closed access
PDF file
RHRubaiyet Haque
Rubaiyet Haque
RVRémy Vié
Rémy Vié
MGMichel Germainy
Michel Germainy
LVLaurie Valbin
Laurie Valbin
PBPatrick Benaben
Patrick Benaben
XBXavier Boddaert
Xavier Boddaert

1 October 2018 in Nano Energy
Verified
Journal Article
Closed access
RHRubaiyet Haque
Rubaiyet Haque
OCOlivier Chandran
Olivier Chandran
SLSébastien Lani
Sébastien Lani
DBDanick Briand
Danick Briand

14 October 2015 in Sensors
Verified
Journal Article
Open access
PDF file
RHRubaiyet Haque
Rubaiyet Haque
Erick OgamErick Ogam
Erick Ogam
CLChristophe Loussert
Christophe Loussert
PBPatrick Benaben
Patrick Benaben
XBXavier Boddaert
Xavier Boddaert
A capacitive acoustic resonator developed by combining three-dimensional (3D) printing and two-dimensional (2D) printed electronics technique is described. During this work, a patterned bottom structure with rigid backplate and cavity is fabricated directly by a 3D printing method, and then a direct write inkjet printing technique has been employed to print a silver conductive layer. A novel approach has been used to fabricate a diaphragm for the acoustic sensor as well, where the conductive layer is inkjet-printed on a pre-stressed thin organic film. After assembly, the resulting structure contains an electrically conductive diaphragm positioned at a distance from a fixed bottom electrode separated by a spacer. Measurements confirm that the transducer acts as capacitor. The deflection of the diaphragm in response to the incident acoustic single was observed by a laser Doppler vibrometer and the corresponding change of capacitance has been calculated, which is then compared with the numerical result. Observation confirms that the device performs as a resonator and provides adequate sensitivity and selectivity at its resonance frequency.

1 March 2018 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
RHRubaiyet Haque
Rubaiyet Haque
PFPierre-André Farine
Pierre-André Farine
DBDanick Briand
Danick Briand

1 March 2025 in AIP Advances
Verified
Journal Article
Open access
RARifat Sarker Apu
Rifat Sarker Apu
NHNazmul Hasan
Nazmul Hasan
RHRubaiyet Haque
Rubaiyet Haque
AKAlamgir Kabir
Alamgir Kabir
MRMd Harunur Rashid
Md Harunur Rashid
The physical, magneto-electronic, optical, and transport characteristics of the noble inorganic f-electron-based double perovskite Sr2PrSnO6 are analyzed, with first-principles density functional theory (DFT) computation for advanced spintronics, optoelectronic, and magneto-RAM applications. The DFT-optimized tolerance factor, formation enthalpy (ΔHf), and structural parameters confirm the ferromagnetic state’s stability in the cubic phase. The density of states profiles and electronic energy band from generalized-gradient approximation + Perdew–Berke–Ernzerhof demonstrate Sr2PrSnO6 half-metallic behavior, exhibiting maximal spin polarization at the Fermi level and dominance by the Pr-f orbital on the event of spin-polarized band edge behavior. Thereby, the Pr-Sn-based double perovskite resembles ferromagnetic behavior, where the total magnetic moment is 3.6 μB, primarily originating from the Pr and Sn atoms at the B-site. The optical properties of Sr2PrSnO6, including high UV absorption, dielectric function, low reflectivity, high refractive index at lower energies, and optical conductivity, indicate its potential for optoelectronic devices. The elastic parameters indicate that Sr2PrSnO6 is ductile, enhancing its suitability for use in the practical industry. Finally, thermodynamic and transport properties were examined for temperatures ranging from 100 to 1000 K. The analysis of transport parameters, namely the Seebeck coefficient, power factor, and thermoelectrical conductivity, shows the material’s enhanced performance at higher temperatures, providing insights into potential applications in spintronics and advanced thermoelectric technologies.

21 June 2019 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
RHRubaiyet Haque
Rubaiyet Haque
DBDanick Briand
Danick Briand
We are reporting on the conversion of gas/air flow energy in pipes to electrical signals using the triboelectric effect. A flapping triboelectric generator design with all freestanding flexible films is introduced in this regard. The generator can be integrated within a regular pipe infrastructure, as it is independent of the pipe material, for implementing the triboelectric effect. All flexible materials are used to develop the triboelectric generator, utilizing a simple fabrication process that is easily scalable. The performance of the triboelectric device was influenced by several physical parameters, as well as by the gas flow speed, which has been optimized here for a pipe diameter of 5 cm. The triboelectric generator implementing a flexible silver material in combination with polytetrafluoroethylene (PTFE) exhibits 100% higher optimum average power output compared to a generator made of PTFE and polyurethane. A harvester unit with two pairs of triboelectric films with an active film area of 5 × 3.3 cm 2 with 6 mm gaps was demonstrated. The device produced total average power of 1.64 mW across an optimum load resistance of 16.7 MΩ under the air flow speed of 9.8 ± 0.2 m s −1 .