The international journal of Aerosol and Air Quality Research (AAQR) covers all aspects of aerosol science and technology, atmospheric science and air quality related issues.
People today spend most of their time indoors; many use fragrances in closed restrooms and bathrooms at home and in public spaces for masking odors. However, volatile organic compounds (VOCs) that are emitted from indoor fragrances have been reported in recent years to pose a risk to health. In this work, microneedle trap samplers (NTSs) were fabricated, packed with sulfonated divinylbenzene (SDVB) adsorbents, and used in passive mode to extract the VOCs that were emitted by bamboo diffusers in fragrance bottles in bathrooms. Instrumental analysis revealed that the main VOCs that were emitted from chemically synthesized fragrances were ethanol (19.2–40.5 ppb), propylene glycol (273.4–527.9 ppb), and 3-ethylbenzaldehyde (3.8–12.4 ppb). Lower indoor air change rates were associated with significantly higher emitted concentrations of VOCs. 3-Ethylbenzaldehyde is a strong respiratory irritant, and outdoor pollutants such as toluene, which escapes from paints, have a negative impact on indoor air quality.
13 December 2013 in Journal of the Air & Waste Management Association
In this study, gaseous benzene, toluene, ethylbenzene, and o-xylene (BTEX) were extracted by passive needle trap samplers (NTS) using divinylbenzene (DVB) particles (mesh sizes 60–80, 80–100, and 100–120, respectively) as packed sorbents. An aspirating pump measured sampling flow rates of NTS, and the relations between BTEX mass and sampling flow rates were sufficient to maintain the extraction performance of these self-designed DVB-NTS. Furthermore, this investigation compared the extraction efficiency of NTS with that of the 100-µm polydimethylsiloxane solid-phase microextration (PDMS SPME) fiber when applied to sample heating products from electric-vaporization anti-mosquito mats, and the experimental results indicated that NTS effectiveness increased with decreasing adsorbent particle diameter. Substantially less mass of gaseous BTEX was extracted using 100-µm PDMS SPME fiber than with NTS of 100–120 mesh DVB for 60-min TWA sampling of anti-mosquito mats. The 100–120 mesh DVB-NTS primarily adsorbed 4.2 ng acetone, 13.3 ng dichloromethane, and 4.5–25.3 ng C10–C12 alkanes.
3 March 2020 in Journal of the Air & Waste Management Association
A solid-phase microextraction (SPME) sampling device, called a needle trap samplers (NTS) that were packed with 60-80 mesh divinylbenzene (DVB) particles, was used to extract indoor volatile organic compounds (VOCs) that were emitted in an oil painting studio. This work compared the sampling performances of a passive NTS and an active charcoal desorption tube that was connected to a personal sampling pump (Method 1501), developed by the National Institute of Occupational Safety and Health, USA. The experimental results reveal that the NTS is a dependable alternative device to Method 1501 for monitoring indoor air quality. 2,2,4,6,6-Pentamethylheptane (isododecane) is the main emitted pollutant when oil painters use odorless thinner as a substitute solvent for turpentine oil, and the mean exposed concentrations of isododecane determined by NTS ranged from 0.83 to 3.10 ppm, which were dependent on whether the indoor ventilation was performed by the natural or mechanic mode. To maintain adequate air exchange rates in an oil painting studio, doors should be opened to increase air circulation, lowering the concentrations of isododecane to which painters are exposed. Implications: A needle trap sampler (NTS) was used to sample VOCs from oil painting in an indoor studio. Isododecane is the main emitted pollutant when painters use the odorless thinner. The NTS was evaluated to be a dependable alternative to Method 1501 for monitoring indoor air quality. To maintain adequate air exchange rates in a painting studio, doors should be opened to lower concentrations of VOCs.
A micro needle trap sampler (NTS) was carried by a mini quadrotor drone (Mavic Pro, DJI) to collect volatile organic compounds (VOCs) from industries. The NTS was fabricated using a 7 cm long, 22-gauge stainless steel needle by packing powdered divinylbenzene (DVB) adsorbents (60–80 mesh diameters). The telescoping sampling shaft was installed on the drone to extend the NTS beyond the downward air turbulence that was caused by the rotation of its propellers. The total mass of the sampling device, including an NTS, a telescoping shaft, a mini-air pump, and an ABS (acrylonitrile butadiene styrene) rack, was not more than 200 g. The emitted VOCs, those from a steel processing plant, including aromatic hydrocarbons (toluene of 15 ppb, ethylbenzene of 9 ppb and p-xylene 12 ppb), and those from a semiconductor processing factory, including trace amounts of methanol (1.96–2.00 ppm), acetone (0.05–0.10 ppm), and toluene (1.04–2.00 ppm), were extracted by the NTS on the drone and identified using a gas chromatography-mass spectroscopy (GC-MS) system in the laboratory. According to the results of VOC detection during the sampling flight of a drone, the stationary pollution sources were successfully identified.