Ravi Kumar Arya

Dr. Ravi Kumar Arya

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2016 in IET Microwaves, Antennas & Propagation
Verified
Journal Article
Open access
PDF file
SZShiyu Zhang
Shiyu Zhang
RARavi Kumar Arya
Ravi Kumar Arya
SPShaileshchandra Pandey
Shaileshchandra Pandey
YVYiannis Vardaxoglou
Yiannis Vardaxoglou
William WhittowWilliam Whittow
William Whittow
RMRaj Mittra
Raj Mittra
The authors introduce two flat graded‐index (GRIN) lens designs in this study. First of these is a thick lens, which was designed and fabricated by using the three‐dimensional (3D)‐printing technique. Second, a thin dial‐a‐dielectric (DaD) lens, which uses state‐of‐the‐art artificially engineered dielectric materials for design and for which they present only the simulated results, with plans to fabricate it in the future. Both designs overcome the difficulties faced in finding desired commercial off‐the‐shelf materials, either for 3D‐printing or for fabricating conventional GRIN lenses. The lenses comprise of several concentric dielectric rings with bespoke relative permittivities for transforming spherical waves into plane waves and vice versa. The 3D‐printed thick flat lens is low‐cost and light‐weight, but provides broadband and high gain performance. Measurement results show that the realised gain of the thick lens is 9–11 dB over the frequency band of 12–18 GHz. The designed DaD lens has the desirable characteristics of low loss, low reflection and broadband properties.

21 December 2020 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Open access
SZShiyu Zhang
Shiyu Zhang
RARavi Kumar Arya
Ravi Kumar Arya
William WhittowWilliam Whittow
William Whittow
DCDarren Cadman
Darren Cadman
RMRaj Mittra
Raj Mittra
Yiannis VARDAXOGLOUYiannis VARDAXOGLOU
Yiannis VARDAXOGLOU
The paper presents the designs of ultra-wideband microwave flat gradient index (GRIN) lenses, which realizes over a 108% fractional bandwidth (12 - 40 GHz). The frequency-independent ray optics method is employed to determine the radially varying permittivity profile of the lenses. The challenge of realizing such a radially varying profile, and the limitations in dielectric material choices, are overcome by two additive-manufacturing-aided approaches: (i) partially infilled dielectrics with a varied periodicity, which ensures the lens performance at the higher end of the frequency range; and (ii) artificially engineered dielectrics (AED) with sub-wavelength-scale metallic inclusions, which enables high permittivity dielectrics and leads to benefits of thickness and mass reduction for the GRIN lenses. Measured results demonstrate that the GRIN lenses improve the gain of open-ended waveguide sources by 8.7 to 15.6 dB over a wide frequency range from 12 to 40 GHz, with the realized gain of up to 23.6 dBi. Both the simulation and measurements of the presented design confirm the potential of implementing the proposed GRIN lens design in high directivity and beamforming antenna applications, across an ultra-wideband frequency range.

6 July 2021 in IETE Journal of Research
Verified
Journal Article
Closed access
AVAkhilesh Verma
Akhilesh Verma
RARavi Kumar Arya
Ravi Kumar Arya
RBRajarshi Bhattacharya
Rajarshi Bhattacharya
RNRaghava N.S
Raghava N.S
In this paper, a novel low profile planar inverted-F antenna (PIFA) with high gain and low specific absorption rate (SAR) using a miniaturized artificial magnetic conductor (AMC) is investigated. The performance of the PIFA antenna is analyzed with AMC to understand the contribution of AMC. The gain enhancement of the PIFA antenna is achieved by applying AMC below the antenna. Furthermore, the placement of AMC also reduces the SAR of the antenna and improves the antenna front-to-back ratio (FBR). The proposed antenna when measured has an impedance bandwidth of 4.8–6.7 GHz (33% with center frequency at 5.75 GHz) which is suitable for Wireless Local Area Network (WLAN), satellite uplink C-band, and sub-6 5G applications with the maximum gain of 7.6 dBi. The performance of the proposed antenna is analyzed by full-wave commercial electromagnetic software and verified by measurements.

1 January 2016 in Progress in Electromagnetics Research C
Verified
Journal Article
Open access
PDF file
RARavi Kumar Arya
Ravi Kumar Arya
SPShaileshachandra Pandey
Shaileshachandra Pandey
RMRaj Mittra
Raj Mittra
In this work, we present a new systematic technique for the design of a flat lens using modified commercial off-the-shelf (COTS) materials, as opposed to metamaterials (MTMs) that are often required in lens designs based on the Transformation Optics (TO) approach. While lens designs based on Ray Optics (RO) do not suffer from the drawback of having to use metamaterials, they still require dielectric materials that may not be commercially available off-the-shelf. This paper describes a systematic procedure for realizing the desired materials by modifying the COTS types, and illustrates its application with some practical examples.

22 September 2022 in Wireless Personal Communications
Verified
Journal Article
Closed access
PDF file
AVAkhilesh Verma
Akhilesh Verma
RARavi Kumar Arya
Ravi Kumar Arya
RNRaghava N.S
Raghava N.S

7 September 2024 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
PCPrashant Chaudhary
Prashant Chaudhary
AKAshwani Kumar
Ashwani Kumar
RARavi Kumar Arya
Ravi Kumar Arya
MAMaifuz Ali
Maifuz Ali