With the recent introductions of glyphosate- and dicamba-tolerant crops, such as soybean and cotton, there will be an increase in POST-applied tank-mixtures of these two herbicides. However, few studies have been conducted to evaluate drift from dicamba applications. This study aimed to evaluate the effects of dicamba with and without glyphosate sprayed through standard and air induction flat-fan nozzles on droplet spectrum and drift potential in a low-speed wind tunnel. Two standard (XR and TT) and two air induction (AIXR and TTI) 110015 nozzles were used. The applications were made at 276 kPa pressure in a 2.2 ms⁻¹ wind speed. Herbicide treatments evaluated included dicamba alone at 560 gaeha⁻¹ and dicamba+glyphosate at 560+1,260 gaeha⁻¹. The droplet spectrum was measured using a laser diffraction system. Artificial targets were used as drift collectors, positioned in a wind tunnel from 2 to 12 m downwind from the nozzle. Drift potential was determined using a fluorescent tracer added to solutions, quantified by fluorimetry. Dicamba droplet spectrum and drift depended on the association between herbicide solution and nozzle type. Dicamba alone produced coarser droplets than dicamba+glyphosate when sprayed through air induction nozzles. Drift decreased exponentially as downwind distance increased and it was reduced using air induction nozzles for both herbicide solutions.

Dicamba plus glyphosate tank mixture have been largely adopted for postemergence weed control after the development of dicamba-tolerant crops. Ammonium sulfate is commonly used as water conditioner (WC) to increase glyphosate efficacy, but its use is restricted for dicamba herbicides. The use of non-AMS water conditioner and other adjuvants could be a way to optimize efficacy of this tank mixture while mitigating herbicide off-target movement. The objective of this study was to determine the physical–chemical properties and droplet size distribution of dicamba and glyphosate solutions with and without non-AMS WC alone and tank mixed with other adjuvants and evaluate the response of weed species to these solutions under greenhouse and field conditions. The adjuvants mostly increased density and viscosity and decreased contact angle and surface tension of herbicide solutions. In presence of WC, except for the adjuvants containing drift reducing agent, Dv_0.5 decreased with the addition of adjuvants. Under greenhouse conditions, biomass reduction increased up to 47 and 33 percentage points for velvetleaf and c. waterhemp when adjuvants were added to solutions without WC, respectively. No increase in control of horseweed and Palmer amaranth was observed with the use of adjuvants under field conditions.

The objective of this work was to evaluate the spray drift and droplet spectrum of dicamba applied alone or with potential drift-reducing adjuvants, using air-induction flat fan nozzles. Standard (XR and TT) and air-induction (AIXR and TTI) nozzles were evaluated in a wind tunnel. The adjuvants used were polymer, ammonium sulfate, vegetable oil, and phosphatidylcholine. The applications were conducted at 276 kPa pressure and 3.5 m s^-1 wind speed. The droplet spectrum was measured using a laser diffraction system. Round strings were used as drift collectors, positioned perpendicularly to the wind direction, at 2, 3, 4, 5, 6, 7, and 12 m from the nozzle. Drift was calculated by quantifying, through fluorimetry, a fluorescent tracer added to each solution at 1 g L^-1. Droplet spectrum and dicamba drift depend on the interaction between spray composition and nozzle type. Air-induction nozzles are more recommended for dicamba applications, especially the TTI nozzle. Polymer and ammonium sulfate increase droplet size in all nozzle types, which may reduce drift to nearby crops.

O sucesso de uma aplicação de herbicida está diretamente relacionado a uma boa deposição da calda no alvo, com o mínimo de perdas para o ambiente. Assim, o presente trabalho objetivou avaliar a deposição e o controle de plantas daninhas promovido pela aplicação de glyphosate em diferentes volumes de calda e com a adição do adjuvante nonil fenol etoxilado. O experimento foi conduzido em delineamento de blocos casualizados com quatro repetições, em esquema fatorial 3x2, sendo três volumes de calda (30, 60 e 150 L ha‑1) e duas composições (com e sem adjuvante adicionado ao tanque). Inicialmente, foi realizada a caracterização físico-química das caldas pulverizadas. Foram avaliados, após a aplicação do glyphosate, utilizando pontas de pulverização hidráulicas de jato plano defletor: deposição de calda no alvo, perdas para o solo e controle de plantas daninhas. O adjuvante promoveu alterações de pequena magnitude nas propriedades físico-químicas da solução. Conclui-se que os menores volumes de calda proporcionaram maiores deposições nas plantas daninhas e menores perdas para o solo. O herbicida estudado proporcionou bom controle das plantas daninhas, independentemente da utilização do adjuvante e do volume de calda.

A pressão de trabalho influencia as características da pulverização hidráulica de produtos fitossanitários e pode alterar a penetração da calda no dossel da cultura da soja. Este trabalho teve como objetivo avaliar o efeito da pressão na deposição de calda em plantas de soja, promovida por diferentes modelos de pontas de pulverização. O experimento foi conduzido em delineamento de blocos ao acaso, em esquema fatorial 2 x 4 + 1, sendo duas pontas de pulverização (jato cônico vazio - ATR e jato cônico vazio com indução de ar - TVI) e quatro pressões de trabalho (689, 1034, 1379 e 1724 kPa), com um tratamento adicional (ponta de jato plano - API, a 448 kPa). A deposição de calda, corrigida para uma mesma taxa de aplicação (200 L ha^-1), pulverizada na cultura da soja (parte superior e inferior do cultivar Vila Rica, em estádio R6), por meio de um pulverizador de barra, foi analisada, empregando-se o traçador fluorescente Rodamina B, detectado por fluorimetria. Também foi avaliado o espectro de gotas, por meio da análise de papéis hidrossensíveis. Concluiu-se que a ponta ATR, que gerou gotas de menor tamanho e mais uniformes, propiciou maior deposição do traçador do que a ponta TVI. O aumento da pressão de trabalho acarretou diminuição da deposição nas folhas da parte inferior da planta. A deposição gerada pela ponta de jato plano (API) não diferiu das geradas pelas demais pontas avaliadas.

The objective of this work was to generate drift curves from pesticide applications on coffee plants and to compare them with two European drift-prediction models. The used methodology is based on the ISO 22866 standard. The experimental design was a randomized complete block with ten replicates in a 2x20 split-plot arrangement. The evaluated factors were: two types of nozzles (hollow cone with and without air induction) and 20 parallel distances to the crop line outside of the target area, spaced at 2.5 m. Blotting papers were used as a target and placed in each of the evaluated distances. The spray solution was composed of water+rhodamine B fluorescent tracer at a concentration of 100 mg L-1, for detection by fluorimetry. A spray volume of 400 L ha-1 was applied using a hydropneumatic sprayer. The air-induction nozzle reduces the drift up to 20 m from the treated area. The application with the hollow cone nozzle results in 6.68% maximum drift in the nearest collector of the treated area. The German and Dutch models overestimate the drift at distances closest to the crop, although the Dutch model more closely approximates the drift curves generated by both spray nozzles.