Similar and dissimilar combinations of a 1000 MPa galvanised dual phase (DP) steel and a 980 MPa transformation induced plasticity (TRIP) steel were resistance spot welded under different welding and heat treatment parameters. The microstructure and mechanical properties of spot welds were evaluated using metallographic technique, microhardness and tensile shear tests. The results showed that the tendency to fail in the pullout mode increased in the order of DP/DP, TRIP/TRIP and DP/TRIP welds, which was caused by the different hardness distribution, carbon equivalent and susceptibility to shrinkage void formation of spot welds for different combinations. In the study of the effects of heat treatments on the DP/TRIP welds, the pre-heating procedure improved the splash of welding to some extent. When the cooling time was larger than or equal to 1000 ms, the post-heating procedure improved the mechanical properties of spot welds owing to the temper of spot weld microstructure.
1 January 2020 in Advances in Materials Science and Engineering
With the gradual depletion of shallow resources, the petroleum industry is developing toward ultradeep wells and high‐speed drillings, and the problems of corrosion and erosion failure of drill pipe materials are becoming more and more serious. On the basis of not destroying the excellent mechanical properties of S135 drill pipe steel, three kinds of coatings, 20% Al‐80% Zn, 30% Al‐70% Zn, and 40% Al‐60% Zn, are cold sprayed on S135 steel. The morphology of the coating is observed, and the bonding strength, porosity, hardness, and corrosion resistance of the coating are tested. Results show that the bonding mechanism between the powder particles and the substrate of the three coatings is mainly mechanical occlusion. From the substrate to the coating surface, the hardness value decreases gradually. With the increase of Al powder content, coating bonding strength increases, coating becomes more compact, and porosity decreases. Corrosion test results show that three coatings can protect the substrate. The density of corrosion products on the coating surface increased with the increase of the Al content. Corrosion potential of the three coatings is lower than that of the substrate, and the corrosion rate of the three coatings is lower than that of the substrate.
Cavitation erosion on the wetted surface of hydraulic machinery is directly related to the cavitation behavior. In this paper, the cavitation behavior and cavitation erosion characteristics on the airfoil surface were observed experimentally, and then, image processing methods for quantifying cavitation structure and cavitation erosion were established. Laser‐CCD system was used to obtain the cavitation structure on the airfoil surface and the microtopographies of the cavitation erosion at different magnifications were obtained by SEM. The distribution and shape of cavitation pits were analyzed. An image processing method based on statistical principle was used to analyze the distribution characteristics of the cavitation structure. The mean and mean square value of the cavitation structure were obtained. The average volume and the volume change rate of cavitation cloud in each position of the flow field during a cavitation period were described. According to the characteristics of cavitation pits, an image processing method based on background correction, edge detection, and binary morphology processing was established, and then, the distribution characteristics and the area of the cavitation pits were obtained. Finally, the effectiveness of the methods is verified by the image processing of cavitation pit in different locations on the hydrofoil.
18 March 2022 in Journal of Materials Engineering and Performance
In this paper, a finite element model for the particle-impact target is established for the abrasion erosion failure behavior of 20# steel used in natural gas gathering pipelines. The JC plastic model and failure criterion are used in the model to simulate the failure and damage of the material, and the reliability of the model was verified by comparison with experimental data. The dynamic behavior of particle erosion was studied by using this model. The changes of energy, stress, and morphology at the microscopic level were analyzed. The influence of particle shape, particle size, impact velocity, and impact angle on the erosion rate of 20# steel was obtained. The model is further used to study the influence mechanism of stress interference on erosion damage behavior under multiparticle random drop impact.
Nine kinds of Al-composite coatings were cold sprayed on the S135 steel. The mechanical properties and microstructures of the coatings were analyzed and the corrosion behavior of the coatings was studied. The surface morphology of the coatings was observed. The porosity of the nine coatings was less than 1.52 %. A proper increase in the Zn powder could reduce the porosity. The thickness of a coating could be increased with an increase in Al2O3 and Zn. The hardness of a coating increased obviously after adding Al2O3. The friction coefficient of a coating decreased with the increase in Zn and Al2O3. The corrosion rate of the coatings decreased with an increase in Al and Al2O3.