The building walls which form the major part of the building envelope thermally interact with the changing surrounding environment throughout the day influencing the indoor thermal comfort of the space. This paper aims at assessing in detail the different aspects (thermophysical properties, thickness, exposure to solar heat gain, etc.) of opaque building wall materials affecting the indoor thermal environment and energy efficiency of the buildings in tropical climate (in the summer and winter days) by conducting simplified simulation analysis using the Integrated Environmental Solutions Virtual Environment (IES-VE) program. Besides, the thermal efficiency of a number of selected wall materials with different thermal properties and wall configurations was analysed to determine the most optimal option for the studied climate. This study first developed the conditions for parametric simulation analysis and then addressed selected findings by comparing the thermal responses of the materials to moderate outdoor temperature and energy-saving potential. While energy consumption estimation for a complete operational building is a complex method by which the performance of the wall materials cannot be properly defined, as a result, this simplistic simulation approach can guide the designers to preliminary analyse the different building wall materials in order to select the best thermal efficiency solution.
Sawdust, which is a waste/by-product of the wood/timber industry, can be utilised as a valuable raw material in building material production due to its abundance and low cost. However, the application of sawdust in the manufacture of unfired clay blocks has received little investigation. Furthermore, the impact of different sawdust particle sizes on the properties of unfired clay blocks has not been studied. Therefore, this study screened sawdust at three different particle sizes: SP-a (212 μm < x < 300 μm), SP-b (425 μm < x < 600 μm) and SP-c (1.18 mm < x < 2.00 mm), to examine their effects on the physical and mechanical properties of unfired clay blocks. The density, linear shrinkage, capillary water absorption and flexural and compressive strengths were among the tests performed. Different sawdust percentages, i.e., 2.5%, 5%, 7.5% and 10% of the total weight of the clay, were considered. The tests results show that when sawdust was added to the mixture, the density of the samples reduced for all particle sizes. However, the linear shrinkage increased in SP-a samples but decreased in the other two particle size samples as the sawdust percentage increased from 2.5% to 10%. On the other hand, the capillary water absorption coefficient increased while the strength decreased with increasing sawdust content for all three groups. The highest compressive strength (CS) and flexural strength (FS) were achieved at 2.5% of sawdust content. Furthermore, it was observed that SP-b (CS—4.74 MPa, FS—2.00 MPa) samples showed the highest strength followed by SP-a (CS—4.09 MPa, FS—1.69 MPa) and SP-c (CS—3.90 MPa, FS—1.63 MPa) samples. Consequently, good-quality unfired clay blocks can be manufactured using sawdust up to 2.5% with particle sizes ranging between 600 and 425 μm.
Agricultural residues/by-products have become a popular choice for the manufacturing of building materials due to their cost-effectiveness and environmental friendliness, making them a viable option for achieving sustainability in the construction sector. This study addresses the utilisation of two agro-wastes, i.e., eggshell and walnut shell, in the manufacture of unburnt clay blocks. The experiments were carried out on three series of samples in which first eggshell (10–50%) and walnut shell (5–20%) were incorporated individually and then combined (5% walnut, 10–30% eggshell) in the mixture to assess their influences on the physical and mechanical properties of the unburnt clay blocks. This study performed the following tests: Density, capillary water absorption, linear shrinkage, flexural and compressive strength. The results indicated that eggshell enhanced the strength relative to the control sample when the materials were employed individually, but walnut shell lowered it. Moreover, combining the two materials in the mixer reduced the strength of the samples even further. Nevertheless, the inclusion of the waste materials decreased the density, capillary water absorption coefficient and linear shrinkage of the samples. The findings indicate that eggshell has great potential for unburnt clay block manufacture. However, walnut shell integration needs further research.