Moon Kwang Um

Moon Kwang Um


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2019 in Journal of Materials Chemistry C
Verified
Journal Article
Closed access
PDF file
OKO. Young Kweon
O. Young Kweon
MLMoo Yeol Lee
Moo Yeol Lee
TPTeahoon Park
Teahoon Park
HJHanbit Jang
Hanbit Jang
AJAyoung Jeong
Ayoung Jeong
JOJoon Hak Oh
Joon Hak Oh
Soft electronic devices are key components of flexible or wearable smart electronics. Chemical sensors based on organic field-effect transistors (OFETs) show great promise because of their high sensitivity, low cost, fast response, flexible applications, and signal amplification via gate voltage tuning. In addition, the sensor response can be made highly selective by incorporating specific functional groups or recognition elements. The response magnitude of an OFET sensor depends strongly on the surface area of the active layer that interacts with the analyte. In this study, two strategies including nanostructuring and surface functionalization have been explored to enhance the performance and sensitivity of OFET sensors. We describe the fabrication of highly flexible, electrospun poly(3,3-didodecylquaterthiophene)/calix[8]arene (PQT-12)/C[8]A sensors employing semiconducting polymer nanofibers (NFs) as the active layer. The resulting bendable and flexible PQT-12/C[8]A OFET sensors show high sensitivity to ethanol (192%) and toluene (229%) and moderate sensitivity to n-hexane (121%) with a minimum detectable level of 10 ppm. In addition, the PQT-12/C[8]A NF sensors are electrically stable under typical operating conditions with a bending radius down to 0.5 mm. This work demonstrates a viable approach for the fabrication of flexible OFETs for use as wearable sensors and health-monitoring devices.

13 November 2017 in Journal of Materials Chemistry C
Verified
Journal Article
Closed access
PDF file
TPTeahoon Park
Teahoon Park
KLKang Eun Lee
Kang Eun Lee
NKNari Kim
Nari Kim
YOYoungseok Oh
Youngseok Oh
JYJung-Keun Yoo
Jung-Keun Yoo
MUMoon Kwang Um
Moon Kwang Um
Structurally controlled zinc oxide (ZnO) nanorods (NRs) were synthesized for ultraviolet (UV) sensing. Concentrations of the zinc precursor and base were controlled to characterize the effects of seeding and growth reaction concentration on the ZnO nanostructures. By increasing the growth concentration, high aspect ratio (maximum 27.3) ZnO NRs were obtained. In addition, we confirmed that the seeding solution concentration was another important factor for ZnO NR synthesis. The formation of ZnO crystal structures was confirmed using X-ray diffraction (XRD), and the structure was well matched to the wurtzite ZnO crystal structure. The morphologies of the crystal structures, including their diameter and length, were determined from field emission-scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) images. The optoelectronic properties were characterized by measuring the photocurrent values during UV sensing. The measured current of the ZnO NRs with a high aspect ratio was 58.5 times higher than that of the ZnO nanoparticles when the applied potential was 10 V and the UV intensity was 840 μW cm−2. To fabricate a wireless smartphone-connected UV sensor platform, a lithium-ion battery, a circuit including a Bluetooth module, a smartphone application, and a developed ZnO NR UV sensor were developed and integrated together. Based on the linear relationship between the photocurrent and UV intensity, the UV irradiation was confirmed in real time on the smartphone screen.

16 August 2016 in Nanomaterials
Verified
Journal Article
Open access
PDF file
YKYoun Kim
Youn Kim
YKYeon Ju Kwon
Yeon Ju Kwon
KLKang Eun Lee
Kang Eun Lee
YOYoungseok Oh
Youngseok Oh
MUMoon Kwang Um
Moon Kwang Um
Jea Uk LeeJea Uk Lee
Jea Uk Lee
Highly flexible and electrically-conductive multifunctional textiles are desirable for use in wearable electronic applications. In this study, we fabricated multifunctional textile composites by vacuum filtration and wet-transfer of graphene oxide films on a flexible polyethylene terephthalate (PET) textile in association with embedding Ag nanoparticles (AgNPs) to improve the electrical conductivity. A flexible organic transistor can be developed by direct transfer of a dielectric/semiconducting double layer on the graphene/AgNP textile composite, where the textile composite was used as both flexible substrate and conductive gate electrode. The thermal treatment of a textile-based transistor enhanced the electrical performance (mobility = 7.2 cm2·V−1·s−1, on/off current ratio = 4 × 105, and threshold voltage = −1.1 V) due to the improvement of interfacial properties between the conductive textile electrode and the ion-gel dielectric layer. Furthermore, the textile transistors exhibited highly stable device performance under extended bending conditions (with a bending radius down to 3 mm and repeated tests over 1000 cycles). We believe that our simple methods for the fabrication of graphene/AgNP textile composite for use in textile-type transistors can potentially be applied to the development of flexible large-area electronic clothes.

21 May 2018 in Materials
Verified
Journal Article
Open access
PDF file
DBDaeryeong Bae
Daeryeong Bae
SKShino Kim
Shino Kim
WLWonoh Lee
Wonoh Lee
JYJin Woo Yi
Jin Woo Yi
MUMoon Kwang Um
Moon Kwang Um
DSDong Gi Seong
Dong Gi Seong
A fast-cure carbon fiber/epoxy prepreg was thermoformed against a replicated automotive roof panel mold (square-cup) to investigate the effect of the stacking sequence of prepreg layers with unidirectional and plane woven fabrics and mold geometry with different drawing angles and depths on the fiber deformation and formability of the prepreg. The optimum forming condition was determined via analysis of the material properties of epoxy resin. The non-linear mechanical properties of prepreg at the deformation modes of inter- and intra-ply shear, tensile and bending were measured to be used as input data for the commercial virtual forming simulation software. The prepreg with a stacking sequence containing the plain-woven carbon prepreg on the outer layer of the laminate was successfully thermoformed against a mold with a depth of 20 mm and a tilting angle of 110°. Experimental results for the shear deformations at each corner of the thermoformed square-cup product were compared with the simulation and a similarity in the overall tendency of the shear angle in the path at each corner was observed. The results are expected to contribute to the optimization of parameters on materials, mold design and processing in the thermoforming mass-production process for manufacturing high quality automotive parts with a square-cup geometry.

1 July 2020 in Journal of Hazardous Materials
Verified
Journal Article
Closed access
BPByeongho Park
Byeongho Park
TPTeahoon Park
Teahoon Park
SKSang-Woo Kim
Sang-Woo Kim
MJMinju Jeong
Minju Jeong
YOYoungseok Oh
Youngseok Oh
MUMoon Kwang Um
Moon Kwang Um

10 October 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HYHyeong Min Yoo
Hyeong Min Yoo
JLJungwan Lee
Jungwan Lee
JKJung Soo Kim
Jung Soo Kim
MUMoon Kwang Um
Moon Kwang Um
In the liquid composite molding process, a binder is used to fix the preform. In this study, the influence of a non-reactive epoxy binder was investigated. To allow the measurement of permeability, the preform specimen was produced under three preforming conditions: neat fabric preform, binder-treated fabric preform without heat treatment, and binder-treated fabric preform with heat treatment. The in-plane directional permeability, K1 (having maximum flow velocity), and K2 (having minimum flow velocity) of the binder-treated fabric preform decreased approximately 80% compared to the neat fabric preform. The permeability in the out-of-plane direction decreased approximately 80% in the binder-treated fabric preform without heat treatment and about 98% in the binder-treated fabric preform with heat treatment. This decrease occurred because the treated binder on the fiber hindered resin impregnation. The effect of the binder on the friction coefficient of carbon fabric was also investigated. The friction coefficient was high when the binder was on the friction surface and increased 40–200% at 110 °C, compared to 25 °C.