Nine asphalt concrete overlays were prepared using three different mix designs: Type C, 12.5 mm Superpave, and Coarse Matrix High Binder Hot-Mix (CMHB-C) mixtures and three different coarse aggregate: siliceous gravel, quartzite and sandstone. Pavement overlays were placed on field sections constructed along IH-20 in Harrison County, Texas. Field sections included each of the nine different surface mixture types. The base course was the same for all surface mixtures and was designed with 90% limestone and 10% local field sand. For all mixtures including the base course, PG 76-22 binder was used. Three pavement condition surveys were conducted on the outside lanes of eastbound and westbound field sections; immediately after, after two years, and after three years of the construction of asphalt concrete pavement system. IRI values were estimated from the left and right wheel paths. Each data-set was analysed separately to compare the pavement smoothness of different asphalt concrete overlays. Section 3 (Superpave quartzite mix) in the westbound lanes and Section 4 (CMHB-C gravel mix) in the eastbound lanes showed the best ride qualities. A paired t-test was conducted for each section in order to assess changes in IRI values with time under real traffic conditions. Test results and statistical analyses indicated that except for the IH-20 westbound left lanes of field Section 3 (i.e. Superpave quartz mix) the IRI values of the asphalt concrete overlays were time stable over the research period of three years.
The engineering properties of base course materials play an important role in the overall stability of a pavement system. The stabilization of sulfate-rich base course materials has been a challenge using traditional calcium-based stabilizers (i.e., cement, lime, and fly-ash) because soluble sulfates present in soils can induce chemical reactions between cement or lime and residual soils, resulting in significant loss of strength and heaving. Introduced as a non-traditional stabilizer, polymer-based products have become popular due to cost efficiency, ease of application, and fast curing times. To explore the feasibility of using polymer-based products for the stabilization of high sulfate soils, a series of unconfined compression strength tests were performed. A sulfate concentration of 20,000 parts per million (ppm) was used in the laboratory testing program. As compared to the strength without soluble sulfate present in the soil, the results revealed a loss of strength in cement, and lime treated specimens but an increase of strength in polymer treated specimens.
19 July 2016 in Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards
The conventional liquefaction potential assessment methods (also known as simplified methods) profoundly rely on empirical correlations based on observations from case histories. A probabilistic framework is developed to incorporate uncertainties in the earthquake ground motion prediction, the cyclic resistance prediction, and the cyclic demand prediction. The results of a probabilistic seismic hazard assessment, site response analyses, and liquefaction potential analyses are convolved to derive a relationship for the annual probability and return period of liquefaction. The random field spatial model is employed to quantify the spatial uncertainty associated with the in-situ measurements of geotechnical material.
The seismic performance of slopes is typically evaluated based on the sliding displacement predicted to occur along a critical sliding surface. A probabilistic assessment of sliding displacement can account rigorously for the aleatory variability in earthquake ground shaking and in the dynamic response and sliding displacement predictions, providing a more complete assessment of the risk associated with seismic slope failure. Rathje and Saygili (2008) developed probabilistic frameworks for the displacement hazard assessment of rigid sliding masses and Rathje et al. (2014) extended these probabilistic frameworks to deeper and/or softer sliding masses. This paper describes efforts to script the developed frameworks within publicly accessible, cloud-based Jupyter notebooks (www.jupyter.org). The developed Jupyter notebooks use as input the yield acceleration (ky) and natural period (Ts) of the slope, and ground motion hazard information in terms of the hazard curve for peak ground acceleration (PGA) and the associated magnitude and distance deaggregations. The Jupyter notebooks are developed to interface directly with the U.S. Geological Survey Unified Hazard Tool such that the required ground motion hazard information can be input directly from the U.S. Geological Survey website. The developed Jupyter notebooks are available to the public as a published dataset within the Data Depot of DesignSafe (www.designsafe-ci.org), the cyberinfrastructure for the Natural Hazards Engineering Research Infrastructure (NHERI).
A 2D dynamic finite element analysis (FEA) was carried out to simulate the stress wave propagation and accumulated strains of a blasting-induced landslide in sensitive clay that took place near the city of Namsos, Norway, in 2009. The blasting triggered a large unintended transient motion of the rock mass with unfavorable weak planes and fault zones. The transient penetration of the rock mass into the clay triggered the devastating slide. A linear elastic model was used for the undrained response of soil. The interaction between soil and the blasted rock was modeled by means of an interface. The blast load was defined as a triangular velocity–time function with a peak value of 10 m/s. In accordance with the field observations after the slide, the predicted deformation of the rock face out into the sensitive clay was around one meter. The results showed a clear trend of the blast impact that diminished with distance. Stability checks using the volume of remolded clay determined from the dynamic analysis revealed that the factor of safety of the slope was reduced to less than unity following the blast.