Halloysite nanotube (HNT) which is cheap, natural, and easily accessible 1D clay, can be used in many applications, particularly heat transfer enhancement. The aim of this research is to study experimentally the pool boiling heat transfer (PBHT) performance of novel halloysite nanofluids at atmospheric pressure condition from typical horizontal heater. The nanofluids are prepared from halloysite nanotubes (HNTs) nanomaterials-based deionized water (DI water) with the presence of sodium hydroxide (NaOH) solution to control pH = 12 to obtain stable nanofluid. The nanofluids were prepared with dilute volume concentrations of 0.01–0.5 vol%. The performance of PBHT is studied via pool boiling curve and pool boiling heat transfer coefficient (PBHTC) from the typical heater which is the copper horizontal tube with a thickness of 1 mm and a diameter of 22 mm. The temperatures of the heated tube surface are measured to obtain the PBHTC. The results show an improvement of PBHTC for halloysite nanofluids compared to the base fluid. At 0.05 vol% concentration, HNT nanofluid has the best enhancement of 5.8% at moderate heat flux (HF). This indicates that HNT is a potential material in heat transfer applications.

Recently, there has been significant interest in the thermal performance of parabolic trough collectors. They are capable of operating and generating highly variable temperature ranges, which can be used in various applications. This paper, therefore, addressed the thermal performance model of using a parabolic trough collector under the radiation intensity level found in Budapest city, as well as the effect of inserting a hybrid nanofluid as the thermal fluid. First, a new modified hybrid nanofluid of alumina and tungsten oxide-based Therminol VP1 is used to enhance the thermal properties of the thermal fluid to be more efficient to use. This enhancement is performed under various volume concentrations and has a volume fraction of 50:50. Second, in order to demonstrate the effectiveness of the thermal element, mathematical energy balance equations were solved and simulated using MATLAB Symbolic Tools. The simulation is presented for two cases: one under a constant radiation intensity and the other under the radiation intensity level of Budapest. For both cases, the results of the dimensionless Nusselt number, heat transfer coefficient, pressure drop, exergy efficiency, and energy efficiency are described. The major findings show that a volume concentration of 4% (Al₂O₃ and WO₃) based Therminol VP1 was the most efficient volume concentrations in both cases. For the first case, the maximum enhancement of the Nusselt number and the heat transfer coefficient are 138% and 169%, respectively. These results enhanced the thermal and exergy efficiencies by 0.39% and 0.385% at a temperature 600 K, flow rate of 150 L/min, and radiation intensity of 1000 W/m². For the second case, the maximum exergy and energy values are recorded at midday under Budapest’s summer climatic conditions and reach 32.728% and 71.255%, respectively, under the optimum temperature of 500 K and flow rate of 150 L/min. Accordingly, the mean improvement in thermal and exergy efficiencies approximately equal to 0.25% at a high concentration, regardless of the season (summer or winter).

This study aims to experimentally investigate the pool boiling heat transfer coefficient behavior using tungsten oxide-based deionized water nanofluids and comparing them to deionized water as conventional fluid. The influence of different dilute volumetric concentrations (0.005%–0.05% Vol.) and applied heat fluxes were examined to see the effect of these parameters on the pool boiling heat transfer performance using nanofluids from a typical horizontal heated copper tube at atmospheric pressure conditions. Results demonstrated that the pool boiling heat transfer coefficient (PBHTC) for both deionized water and nanofluids increased with increasing the applied heat flux. The higher PBHTC enhancement ratio was 6.7% for a volume concentration of 0.01% Vol. at a low heat flux compared to the deionized water case. Moreover, the PBHTC for nanofluids was degraded compared to the deionized water case, and the maximum reduction ratio was about 15% for a volume concentration of 0.05% Vol. relative to the baseline case. The reduction in PBHTC was attributed to the deposition of tungsten oxide nanoflakes on the heating surface during the boiling process, which led to a decrease in the density of the nucleation sites.

Development of thermal efficiency of the concentrated solar energy especially parabolic trough collector using various nanofluids types has a taken high interest in recent years. In this article enhancement thermal performance inside the heating collecting element of trough collector type LS-2 was simulated and improved using nanofluid consist of Tungsten Oxide WO₃ inserting in Syltherm 800. Nanofluid effect was examined by solving the energy balance equation using MATLAB Software to cover wide range concentration volume 1-5% and inlet temperatures ranging from 350-650 K for the turbulent flow. The heat transfer performance and thermal efficiency were improved based on the results, and a notable increase was obtained when volume concentration had been increased compared with base fluid.

This study aims to experimentally investigate the nucleate pool boiling heat transfer performance of magnesium oxide nanoparticles MgO based deionized water nanofluid at the atmospheric pressure condition. Dilute volumetric concentrations within a range of 0.001% to 0.01% Vol. were used to examine the pool boiling heat transfer performance represented by pool boiling curve, and pool boiling heat transfer coefficient. The heating element was a horizontal copper heated tube with a typical diameter 22 mm submerged inside the cubic boiling chamber. Efforts have been made to measure the surface temperatures along the heated tube to ensure the proper and accurate heat transfer coefficient calculations in this work. The results indicated that the pool boiling heat transfer coefficient enhancement ratio (PBHTC /PBHTC ) was intensified for volume fractions i.e. 0.001%, 0.004%, and 0.007% Vol. while it was degraded for volume concentrations i.e. 0.01%, and 0.04% Vol. compared to deionized water as baseline case.