Atomization of emulsions with pressure swirl atomizers is a common task in food process engineering. Especially in spray drying processes for food materials like dairy products, it is the technology of choice. During atomization, emulsions are subjected to high stresses, which can lead to deformation and breakup of the dispersed droplets. In this study, the influence of atomization pressure (5–20 MPa) and initial oil droplet size (0.26, 3.1, and 20.8 μm) on the oil droplet breakup during atomization of food based oil‐in‐water emulsions with pressure swirl atomizers was investigated. It was shown that a significant oil droplet breakup takes place upon atomization. The size of oil droplets with an initial value of 3.1 and 20 μm was reduced up to 0.36 μm. No breakup of oil droplets with an initial value of 0.26 μm was observed. The breakup was highly dependent on the atomization pressure. The results were analyzed based on existing knowledge on droplet breakup in laminar flow. A concept to estimate capillary numbers during atomization was developed based on common models from different applications. The results of this study can be used to control the resulting oil droplet size after atomization with pressure swirl atomizers.Practical application: Spray drying of emulsions is a widely used process in the food industry to produce products with encapsulated oily components. Product examples include infant formula, milk powder, and the encapsulation of aroma and coloring compounds. Breakup of the oil droplets during the atomization step of spray drying can change a previously adjusted and desired oil droplet size. As the oil droplet size in the final product can be responsible for several properties like sensorial aspects and stability, a control of oil droplet breakup is essential. Pressure swirl atomizers are widely used in industrial applications as atomization devices. In this study, oil droplet breakup during atomization with these atomizers was investigated. The findings in this study allow a better control of the oil droplet size during atomization in practical applications.
Pea and amylomaize starches were used to produce aerogel in form of monoliths and microparticles. The formation of starch gel was investigated, and we showed that each starch needed a different pasting temperature for its complete dissolution. The gelation kinetics was investigated with oscillatory rheometry for both systems as a function of the starch concentration. The gelation and retrogradation temperature of the starch gel were varied and its impact on the final aerogel evaluated. The emulsion gelation was carried out batch wise in a stirred vessel with different impeller geometries, concentrations of surfactant (Span80 and PGPR) and stirring rates. A particle size prediction approach based on idealized flow (Couette, 2D hyperbolic and turbulent) during the emulsification was proposed. A semi-continuous set-up for the emulsion gelation was developed in which the emulsification occurs in a single pass through a colloid mill and the gelation is triggered in-line with a counter-current heat exchanger.
23 July 2021 in Journal of Food Processing and Preservation
The goal of this study was to investigate the influence of the emulsifier system on the changes in oil droplet size occurring during the drying step of spray drying of emulsions. Atomization and spray drying experiments were performed with emulsions stabilized with whey protein isolate (WPI) alone or in combination with low molecular weight emulsifiers (lecithin, mono- and diglycerides (MoDi) and citrem). Oil droplet coalescence was observed for the systems WPI/Citrem and WPI/MoDi, as the d90,0 increased from 0.86 ± 0.16 µm and 1.67 ± 0.35 µm after atomization to 1.83 ± 0.24 and 1.90 ± 0.17 µm after drying, respectively. Oil droplets stabilized with WPI or WPI/Lecithin remained stable during drying. Measurements of dilatational rheology of the interfacial film showed that phase angle values increase in the order WPI/Lecithin<WPI<WPI/Citrem=WPI/MoDi. Therefore, in the studied system oil droplet coalescence during drying increases when the elastic behavior of the interfacial film decreases.
To correlate the viscosity of camel milk with its atomization properties, first, the viscosity profiles of camel milk are compared with model milk systems (reconstituted skimmed cow milk powder). Then, atomization experiment was conducted using model milk systems and finally, the findings of the atomization experiments were coincided with the viscosity profiles. The effect of total solids of whole (10% to 40%) and skimmed (7.5% to 30%) camel milks on its viscosity was investigated. At 30% total solids level and a temperature of 20 °C, skimmed camel milk exhibited a viscosity of 7.68 mPa.s whereas whole camel milk 8.96 mPa.s. This value is small compared to suspension of reconstituted skimmed cow milk powder, which reached up to 18.55 mPa.s and to that of suspension of whey protein concentrate (28.15 mPa.s). By raising the total solid from 20% to 30%, it was shown that, the average spray droplet size would be changed from 18.77 to 29.40 µm and the span from 1.76 to 1.55. Based on their viscosity profiles, these values would be obtained for camel milk at total solid values of 35% for whole and 38% for skimmed milks. This would allow camel milk to be concentrated to higher total solid levels than bovine milk. Practical Application: Converting camel milk into powder by spray drying will have a great role in its commercialization. To do so, establishing knowledge on the viscosity of camel milk at different total solids levels in relation to its atomization properties would be of paramount importance. Because, this would enable us to fine tune the viscosity of the milk to arrive at a quality powder with all the desired techno‐functional properties. Moreover, it will also contribute by furnishing engineering data pertinent to the development, design, or choice of appropriate nozzles for atomization of the milk during spray drying at different drying set ups.
Spray drying of whey protein-based emulsions is a common task in food engineering. Lipophilic, low molecular weight emulsifiers including lecithin, citrem, and mono- and diglycerides, are commonly added to the formulations, as they are expected to improve the processing and shelf life stability of the products. During the atomization step of spray drying, the emulsions are subjected to high stresses, which can lead to breakup and subsequent coalescence of the oil droplets. The extent of these phenomena is expected to be greatly influenced by the emulsifiers in the system. The focus of this study was therefore set on the changes in the oil droplet size of whey protein-based emulsions during atomization, as affected by the addition of low molecular weight emulsifiers. Atomization experiments were performed with emulsions stabilized either with whey protein isolate (WPI), or with combinations of WPI and lecithin, WPI and citrem, and WPI and mono- and diglycerides. The addition of lecithin promoted oil droplet breakup during atomization and improved droplet stabilization against coalescence. The addition of citrem and of mono- and diglycerides did not affect oil droplet breakup, but greatly promoted coalescence of the oil droplets. In order to elucidate the underlying mechanisms, measurements of interfacial tensions and coalescence times in single droplets experiments were performed and correlated to the atomization experiments. The results on oil droplet breakup were in good accordance with the observed differences in the interfacial tension measurements. The results on oil droplet coalescence correlated only to a limited extent with the results of coalescence times of single droplet experiments.