The wireless actuation of magnetic soft architectures can enable complex functionalities important in biomedicine and soft robotics. However, transforming and maintaining a device’s desired geometry without a sustained energy input remains challenging, especially where environmental stresses can be unpredictable. Here, we create a soft multistable magnetic-responsive metamaterial with programmable energy barriers enabled by a bistable geometry made entirely from soft material. The multistability and magnetic programming enable the soft metamaterials to reversibly transform between stable states, even under mechanical and thermal stresses that far exceed physiological conditions. In addition, the metamaterials can sustain compressive loads more than 10 times their mass, achieve shape reconfiguration in remote and confined spaces, and wirelessly deliver fluids against pressure, suggesting a broad range of future biomedical and soft robot applications.
Wind energy is one of the fastest growing renewable energy sources in the U.S. Wind turbine wakes change the flow field within wind farms and reduce power generation. Prior research has used experimental and computational methods to investigate and model wind farm wake effects. However, these methods are costly and time-consuming to use commercially. In contrast, a simple analytical approach can provide reasonably accurate estimates of wake effects on flow and power. To reducing errors in wake modeling, one must calibrate the model based on a specific wind farm setting. The purpose of this research is to develop a calibration procedure for wind farm wake modeling using a simple analytical approach and wind turbine operational data obtained from the Supervisory Control And Data Acquisition (SCADA) system. The proposed procedure uses a Gaussian-based analytical wake model and wake superposition model. The wake growth rate varies across the wind farm based on the local streamwise turbulence intensity. The wake model was calibrated by implementing the proposed procedure with turbine pairs within the wind farm. The performance of the model was validated at an onshore wind farm in Iowa, USA. The results were compared with the industry standard wind farm wake model and shown to result in an approximate 1% improvement in sitewide total power prediction. This new SCADA-based calibration procedure is useful for real-time wind farm operational optimization.
Solute–surface interactions have garnered considerable interest in recent years as a novel control mechanism for driving unique fluid dynamics and particle transport with potential applications in fields such as biomedicine, the development of microfluidic devices and enhanced oil recovery. In this study, we will discuss dispersion induced by the diffusioosmotic motion near a charged wall in the presence of a solute concentration gradient. Here, we introduce a plug of salt with a Gaussian distribution at the centre of a channel with no background flow. As the solute diffuses, the concentration gradient drives a diffusioosmotic slip flow at the walls, which results in a recirculating flow in the channel; this, in turn, drives an advective flux of the solute concentration. This effect leads to cross-stream diffusion of the solute, altering the effective diffusivity of the solute as it diffuses along the channel. We derive theoretical predictions for the solute dynamics using a multiple-time-scale analysis to quantify the dispersion driven by the solute–surface interactions. Furthermore, we derive a cross-sectionally averaged concentration equation with an effective diffusivity analogous to that from Taylor dispersion. In addition, we use numerical simulations to validate our theoretical predictions.
The motion of finite-length cylindrical rods moving near a planar rigid surface is a scenario common across many engineering and natural settings. We study the low-Reynolds-number flow around finite rods that are allowed to rotate or translate in directions perpendicular or parallel to the plane. We develop a three-dimensional lubrication theory to characterize the pressure and hydrodynamic resistances of the cylinders through a special consideration of the cylinder's end effects. In addition, we use three-dimensional numerical simulations to solve these Stokes flows for cylinders of varying lengths and with varying gap sizes between the cylinder and plane, and the numerical results support the developed analytical descriptions. We also use visualizations of the flow to provide qualitative insights and rationalize the effect of the ends on the dynamics of the cylinders. The numerical simulations and theoretical predictions show good agreement in the long (isolated ends) and short (disk-like) limits.
Soft robotic swimmers that can mimic the flagella-powered locomotion of micro-organisms are of significant interest in a broad range of applications. However, realising micro-organisms' dexterity in soft robots remains challenging without an effective mechanism to achieve bidirectional propulsion in low Reynolds numbers. Here, inspired by recent theoretical studies that suggest the possibility of intrinsically curved elastic flagella to achieve bidirectional propulsion, we experimentally investigated the propulsion behaviour of elastic artificial flagella with uniform intrinsic curvature, actuated by transverse oscillations at Re < 0.1. Our results reveal that the flagella’s curvature influences the propulsion direction and magnitude, suggesting a transition between positive and negative propulsion when the flagella’s central angle in the stress-free state (θ0) is between 60° and 90° at Sp = 1.5 and 1.8. We also investigate the relationship between the propulsion force and flagella oscillation with numerical simulations. These findings suggest the potential of on-demand curvature modulation during active oscillation to achieve bidirectional propulsion, enhancing the dexterity in flagella-driven artificial swimmers for a broad range of applications in microscale systems.
Three-dimensional (3D) printing can create freeform architectures and electronics with unprecedented versatility. However, the full potential of electronic 3D printing has so far been limited by the inability to selectively anneal the printed materials, especially on temperature-sensitive substrates. Here, we achieve highly selective and rapid volumetric heating of 3D-printed nanomaterials and polymers in situ by focusing microwaves using a metamaterial-inspired near-field electromagnetic structure (Meta-NFS). In contrast to previous work, the Meta-NFS achieves the spatial resolution and power density needed to 3D print freeform microstructures where the electronic and mechanical properties can be locally programmed even within optically opaque materials. By broadening the material palettes compatible with 3D printing, near-field microwave 3D printing with Meta-NFS enables classes of electronics that are otherwise challenging to create.