To improve the problem of collapsibility of loess, adding industrial materials such as cement is common engineering treatment, but this seriously damages the reclamation performance of soil. Calcium lignosulfonate (CLS) from paper plant waste fluids is a natural bio-based polymer with good application prospects as a soil improver. In this paper, the collapsibility and mechanical properties of CLS improved loess were investigated using a collapsibility test, gray correlation analysis, and an unconfined compressive strength test (UCS). In addition, the strengthening mechanism of CLS-improved loess was also explored based on scanning electron microscopy (SEM), microstructure parameters, and X-ray diffraction. The collapsibility coefficient decreased rapidly after CLS was admixed, and the single and double-oedometer methods showed the same change trend. The order of grey correlation degree of collapsibility on each index from large to small was: moisture content, pore ratio, dry density, and CLS content. The dosage of CLS greatly influenced the mechanical properties and collapsibility of stabilized loess. The optimum amount of CLS for Xi’an loess was 3%, at which the collapsibility coefficient was reduced by more than 95%, and the 28 d UCS increased by 180.01%. From the microstructure and mineral composition analysis perspective, CLS plays a role in filling pores and linking soil particles. After the protonation and ion exchange effect of CLS, the grain size and double electric layer thickness of mineral composition were reduced, and the structural compactness was increased. These research results are of great scientific significance for the ecological modification of soils.

Improvement of geotechnical properties of soil by cementitious additives and nanomaterials is commonly used method. However, few systematic research studies on the co‐effects of them on the geotechnical properties of loess have been explored. In the present research, the enhancement technique of loess was proposed based on the co‐effects of graphene oxide (GO) and cement. In addition, the compactability, mechanical properties, water resistance, and microstructure of the GO/cement/loess ternary system were studied. The results revealed that, with the increase of incorporation of GO (0.03, 0.06, 0.09, and 0.12 wt. %), the optimum moisture decreased, while the dry density, mechanical properties, and water resistance increased significantly. And an optimum GO content of 0.09 wt. % was determined according to mechanical properties and water resistance. Moreover, the scanning electron microscope (SEM) results revealed that the microstructure was densified and the characteristics of pores were refined. And the co‐work mechanisms of GO/cement on loess were summarized. All the results indicated that the GO/cement mixture has remarkable co‐effects on the geotechnical properties of loess.

This paper presents an analysis of bamboo bolt‐modified slurry interfaces based on 26 in situ axial pull‐out tests intended to highlight the mechanical behavior of interface under a fracture mode. Three impact factors are analyzed: anchorage length, bolt diameter, and bolt hole diameter, using the same materials of bamboo and modified slurry. The result shows that the interface between the bamboo bolt and anchoring agent is the control interface of an anchorage system, and the local behavior of the interface involves four stages: elastic, soften, friction, and decoupling. Distribution law and change trend of slippage, stress, and strain of anchoring interface along with the axial direction of an anchor bolt were analyzed. The result shows that there is effective anchoring length limit in this kind of interface, and that the complete decoupling phenomenon should not be neglected. Through a comparative analysis of the existing bond‐slip model and interface bond‐slip curve, and considering the correspondence of the strain‐slip curve and trilinear bond‐slip model simultaneously, a modified trilinear bond‐slip model has been proposed. The friction section of this model is limited, and shearing stress in the complete decoupling section is zero.

This paper takes the preservation works on the archaeological sites of Gaochang Ruins, Xinjiang, as background. Based on the soil characteristics analysis on the archaeological sites, experimental studies were conducted on the consolidation effect of the BS-10 consolidation material on the archaeological sites of adobe and rammed earth. The results showed the following:, after consolidation, the wind erosion resistance of the soil on the archaeological sites was substantially increased, and the wind erosion modulus was reduced by 5~8 times; the soil exhibited fine grid structure and significantly reduced degree of permeability, while still maintaining the moisture exchange between inside and outside the soil; there is excellent ageing resistance; the resistance to freezing and thawing was closely related to the soil water content and had little influence in arid regions; the water resistance was improved and could satisfy the requirements for consolidating the sites in arid regions; the unconfined compressive strength was improved moderately, which was the key direction of improvement in the future, and the consolidated soil did not form duricrust on the surface and had good bonding strength with the internal parts. The BS-10 material can meet the consolidation requirements for the earthen archaeological sites in arid regions of northwest China.

The anchoring technology is extensively applied in reinforcing protection of the earth relics. Now that no specification is available for different new anchor rods in earth relics protection due to diversified destruction modes of earth relics and complexity of engineering technology conditions, it is urgent to guide reinforcing design and construction with a complete detailed anchor rod research document. With the new carbon fiber Phyllostachys pubescens anchor rod as the research object, six lots of in situ tests are designed to, respectively, study the destruction mode and anchoring performance of the carbon fiber Phyllostachys pubescens anchor rod under different anchor length L, anchor rod diameter D, bore diameter H, grouting material S, rib spacing R, and inclination angle A in this paper. By studying load shift curve experiment in drawing of the anchor rod, the destruction mode and ultimate bearing capacity of the carbon fiber Phyllostachys pubescens anchor rod in different experiment lots are obtained, and the concept of permitted application value N in anchor rod design is proposed. By studying strain distribution characteristics of anchor rods in experimental lots along the length direction under action of the permitted application value N and combining the existing destruction mode and ultimate bearing capacity, this paper analyzes influences of L, D, H, S, R, and A on anchoring effect of the carbon fiber Phyllostachys pubescens anchor rod; gives the reasonable value range of L, D, H, and R when the carbon fiber Phyllostachys pubescens anchor rod is used for reinforcing design of the earth relics; and provides favorable experiment basis for reinforcing design of the earth relics based on the carbon fiber Phyllostachys pubescens anchor rod.