Tao Yin

Dr. Tao Yin

Quzhou University

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 November 2018 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
TYTao Yin
Tao Yin
TDTosiro Doi
Tosiro Doi
SKSyuhei Kurokawa
Syuhei Kurokawa
ZZZhao Zhong Zhou
Zhao Zhong Zhou
KFKai Ping Feng
Kai Ping Feng

4 July 2022 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
KFKaiping Feng
Kaiping Feng
Binghai LyuBinghai Lyu
Binghai Lyu
TZTianchen Zhao
Tianchen Zhao
TYTao Yin
Tao Yin
ZZZhaozhong Zhou
Zhaozhong Zhou

1 February 2021 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
PDF file
TYTao Yin
Tao Yin
PZPan Pan Zhao
Pan Pan Zhao
TDToshiro Doi
Toshiro Doi
SKSyuhei Kurokawa
Syuhei Kurokawa
JJJinyun Jiang
Jinyun Jiang
The objective of this study was to realize high-efficiency and high-quality chemical mechanical polishing (CMP) of a silicon carbide (SiC) substrate. Consequently, the effect of a gas atmosphere on the CMP characteristics of a SiC substrate was investigated. The experimental results show that increasing the partial pressure of oxygen (O2) in the atmosphere to 300 kPa led to an over 2-fold increase in the material removal rates (MRRs) of the Si and carbon (C) faces compared to an open-air atmosphere. White light interference microscopy, energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS) were used to analyze the face morphology and surface elements after processing. Si face atoms were more difficult to oxidize than C face atoms, resulting in a low MRR of the Si face after CMP. The MRR of the Si face was improved by using an ultraviolet (UV) photocatalysis reaction in the high-pressure O2 atmosphere. Excitation of O2 molecules in the slurry into HO 2 • with a stronger oxidation capability promoted the chemical reaction at the solid-liquid interface. The processing mechanism was elucidated.

1 July 2022 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
PZPanpan Zhao
Panpan Zhao
TYTao Yin
Tao Yin
TDToshiro Doi
Toshiro Doi
SKSyuhei Kurokawa
Syuhei Kurokawa
KSKiyoshi Seshimo
Kiyoshi Seshimo
JCJianchen Cai
Jianchen Cai
High-efficiency and high-quality chemical mechanical polishing (CMP) of silicon carbide (SiC) substrates was achieved using slurries prepared with manganese oxide (MnO 2 , Mn 2 O 3 ) particles. Experimental results showed that the oxidation-reduction potential (ORP) and zeta potential of these manganese (Mn)-based slurries decreased with increasing pH. For alkaline pH values (> 7), MnO 2 particles were converted into strongly oxidizing MnO 4 2− ions that promoted interfacial chemical reactions during CMP, thereby increasing the material removal rate. Observation and analysis of the SiC substrate surface showed that the surface roughness (Ra) reached 1 nm after polishing, but slight surface scratches remained. The binding energy of elemental oxygen (O) and Mn (O1s and Mn2p) indicated that the atoms on the substrate surface underwent an oxidation reaction, which weakened the Si-C molecular bond and thus increased the material removal rate.

23 March 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
JCJianchen Cai
Jianchen Cai
JJJiaxi Jiang
Jiaxi Jiang
JJJinyun Jiang
Jinyun Jiang
TYTao Yin
Tao Yin
XGXiang Gao
Xiang Gao
Yiqiang FanYiqiang Fan
Yiqiang Fan
This study proposed a fabrication method for thin, film-based, transparent, and flexible digital microfluidic devices. A series of characterizations were also conducted with the fabricated digital microfluidic devices. For the device fabrication, the electrodes were patterned by laser ablation of 220 nm-thick indium tin oxide (ITO) layer on a 175 μm-thick polyethylene terephthalate (PET) substrate. The electrodes were insulated with a layer of 12 μm-thick polyethylene (PE) film as the dielectric layer, and finally, a surface treatment was conducted on PE film in order to enhance the hydrophobicity. The whole digital microfluidic device has a total thickness of less than 200 μm and is nearly transparent in the visible range. The droplet manipulation with the proposed digital microfluidic device was also achieved. In addition, a series of characterization studies were conducted as follows: the contact angles under different driving voltages, the leakage current density across the patterned electrodes, and the minimum driving voltage with different control algorithms and droplet volume were measured and discussed. The UV–VIS spectrum of the proposed digital microfluidic devices was also provided in order to verify the transparency of the fabricated device. Compared with conventional methods for the fabrication of digital microfluidic devices, which usually have opaque metal/carbon electrodes, the proposed transparent and flexible digital microfluidics could have significant advantages for the observation of the droplets on the digital microfluidic device, especially for colorimetric analysis using the digital microfluidic approach.

13 April 2021 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
TYTao Yin
Tao Yin
ZWZhiDa Wang
ZhiDa Wang
TDToshiroh Karaki Doi
Toshiroh Karaki Doi
SKSyuhei Kurokawa
Syuhei Kurokawa
ZTZHE TAN
ZHE TAN
HLHuan Lin
Huan Lin