Silicon is one of the most promising anode materials for lithium-ion batteries. To solve the problems associated with the great volume expansion of Si during lithium storage, nano-sized Si particles are generally employed. However, their high surface activity is likely to trigger considerable electrolyte decompositions at low potential, thus the surface of these Si nano-particles need further chemical modifications. In this paper, three kinds of functional groups were grafted onto the surface of Si particles by different chemical treatments. X-ray photoelectron spectroscopy (XPS) studies proved that the structure of solid electrolyte interface (SEI) film formed on the surface of Si nano-particles depends greatly on the surface modification strategy. Electrochemical characterizations like electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) etc., also verified the distinct effects of these functional groups on the surface of nano-sized Si electrodes. The relationship between surface functional groups and electrochemical performance of the nano-Si anode material was addressed.
30 September 2016 in Journal of Materials Chemistry A
The interactions between silicon particles and polymeric binders are a key factor during the course of manufacturing high-capacity Si anodes for lithium-ion batteries. Polymeric binders usually compensate for the volumetric over-changes of silicon particles, and then prevent electrode deformation while keeping the integrity of electron and ion pathways. This work explores an efficient synthesis method to directly anchor a reliable binder tightly on the surface of Si particles by in situ polymerization of an acrylic acid monomer in the mixing process of Si-based slurry. The resultant Si composite electrode possesses a highly elastic structure, which can provide a highly extensible space accommodating volume expansion/contraction of Si particles during lithiation/delithiation. Moreover, the cross-linked acrylic acid network results in a strong cohesive force between Si particles and auxiliary materials, such as conductive agent and copper foil. Accordingly, a satisfactory electrochemical performance of the Si anode can be gained, including a high initial coulombic efficiency of ∼73% and stable cycling performance (∼82% retention over 300 cycles at a current density of 4 A g−1). Such a novel and facile fabrication process represents an appealing method for manufacturing high-performance Si-based anodes using micron-sized Si particles with low cost.
Herein, FePO4 was for the first time proposed to serve as an anode material (the sodium intercalation host), to obtain novel sodium-based dual-ion batteries.
Developing a sacrificial agent-free Zn1−xCdxS-based photocatalyst for efficient photocatalytic overall water splitting (POWS) is economical and eco-friendly but a challenging task. Herein, we synthesize a phosphorus (PO) protection layer and non-precious FexCoyNizP and MnOa cocatalysts on Zn0.4Cd0.6S by a safe and energy-saving two-step photochemical strategy. The prepared Zn0.4Cd0.6S/PO/FexCoyNizPi–MnOa photocatalyst displays average hydrogen and oxygen evolution rates of ∼1.14 mmol h−1 g−1 and ∼0.54 mmol h−1 g−1 in POWS, respectively, where FexCoyNizP and MnOa act as the photogenerated electron and hole acceptors and provide the active sites for the two reactions. The superior POWS performance was maintained for 12 hours without any obvious attenuation. Moreover, photocatalytic partial water splitting (PPWS) is induced by the oxidation of NaH2PO2 during the photochemical synthesis process, yielding hydrogen evolution rates of 7.22 mmol h−1 g−1 and 5.90 mmol h−1 g−1, respectively. By integrating the two-step photochemical synthesis and POWS process (PPWS → PPWS → POWS), we obtain a total H2 yield of about 4.85 mmol under 17 h visible light irradiation, which corresponds to an average H2 evolution rate of 0.29 mmol h−1. This work develops a safe and energy-saving photochemical synthesis strategy for Zn1−xCdxS-based photocatalysts, which not only exhibits excellent POWS performance but opens an avenue for the tandem application of PPWS and POWS to achieve a high H2 total yield for solar-energy conversion.