We report a high power and high energy all-fiber-based single frequency nanosecond pulsed laser source at ~1918.4 nm in master oscillator-power amplifier (MOPA) configuration. The pre-shaped pulsed fiber laser seed with a variable pulse duration and repetition rate were achieved by directly modulating a continuous wave (CW) single frequency fiber laser using a fast electro-optical modulator (EOM) driven by a arbitrary waveform generator (AWG). One piece of single mode, large (30 μm) core, polarization-maintaining (PM) highly thulium-doped (Tm-doped) germanate glass fiber (LC-TGF) was used to boost the pulse power and pulse energy of these modulated pulses in the final power amplifier. To the best of our knowledge, the highest average power 16 W for single frequency transform-limited ~2.0 ns pulses at 500 kHz was achieved, and the highest peak power 78.1 kW was achieved at 100 kHz. Furthermore, mJ pulse energy was achieved for ~15 ns pulses at 1 kHz repetition rate. Theoretical modeling of the large-core highly Tm-doped germanate glass double-cladding fiber amplifier (LC-TG-DC-FA) is also present for 2 μm nanosecond pulse amplification. A good agreement between the theoretical and experimental results was achieved. The model was also utilized to investigate the dependence of the stored energy in the LC-TGF on the pump power, seed energy and repetition rate, which can be used to design and optimize the LC-TG-DC-FA to achieve higher pulse energy.
We report a unique all fiber-based single-frequency Q-switched laser in a monolithic master oscillator power amplifier configuration at by using highly Tm-doped germanate fibers for the first time. The actively Q-switched fiber laser seed was achieved by using a piezo to press the fiber in the fiber Bragg grating cavity and modulate the fiber birefringence, enabling Q-switching with pulse width and repetition rate tunability. A single-mode polarization maintaining large core highly Tm-doped germanate fiber was used in the power amplifier stage. For pulses with repetition rate, we achieved pulse energy, which corresponds to a peak power of with transform-limited linewidth.
22 November 2019 in Journal of Lightwave Technology
The spectroscopic properties of Er3+-doped tellurite glasses were investigated and a 1 wt.% Er3+-doped tellurite fiber was fabricated for L-band lasers. Wavelength-tunable fiber lasers in a linear cavity based on Littrow configuration were developed and studied with different gain fiber lengths as well as output coupling ratios. Wavelength tunable range of 38 nm from 1589 to 1627 nm was achieved in the experiment with a 3-m Er3+-doped tellurite fiber laser pumped at 1570 nm. A maximum output power of 52.4 mW was obtained at 1614 nm. Compared to L-band Er3+-doped silica fiber lasers, the demonstrated Er3+-doped tellurite fiber lasers exhibit much higher optical signal-to-noise ratio (>30 dB) even at the longest operating wavelength of 1627 nm. Our simulation shows that the laser wavelength can be further extended to 1634 nm if the tellurite fiber loss is improved and the fiber cavity is optimized.
We report on an eye-safe, transform-limited, millijoule energy, and high average power fiber laser. The high gain and short length of the NP phosphate-glass fibers enable the SBS-free operation with kW level peak power. The output energy is up to 1.3 mJ, and the average power is up to 23 W at an 18 kHz repetition rate with 600 ns pulses (peak power > 2.1 kW). The PER is ≈16 dB and the M2 of the beam is 1.33 × 1.18. The coherent LIDAR Figure Of Merit (FOM) is 174 mJ*sqrt(Hz), which to our knowledge is the highest reported for a fiber laser. We also report 0.75 mJ energy and >3.7 kW peak power with down to 200 ns pulses and up to 1.21 mJ energy with a 3–5 kHz repetition rate operation of the current system.
8 December 2020 in Journal of Lightwave Technology
Single-frequency distributed Bragg reflector fiber laser at 915 nm was demonstrated by using a 2.5-cm long ${Nd^{3+}}$ -doped phosphate fiber as the gain medium. An output power of 13.5 mW was obtained at an absorbed pump power of 240 mW. Our experimental results show that ${Nd^{3+}}$ -doped phosphate glass fiber is more efficient than ${Nd^{3+}}$ -doped silica glass fiber for single-frequency laser operation in the 900 nm wavelength range.
We report an Er-doped, actively Q-switched, fiber laser, generating transform-limited pulses based on single-frequency fiber laser seeded ring cavity. The output pulsewidth can be tuned from hundreds of nanoseconds to several microseconds by changing the repetition rate or the open time of the electrical pulse trigger. This injection-seeded, Q-switched ring cavity fiber laser can be operated over the whole C-band. In addition, a theoretical model is developed to numerically study the pulse characteristics by changing the acousto-optic modulator transmission as well as several cavity parameters, such as the cavity length and loss. The numerical results are in good agreement with the experimental results.