Aminophosphonates were chosen for a first step functionalization of TiO2 grown on titanium as they possess a phosphonate group on one end, that can be exploited for coupling with the oxide surface, and an amino group on the other end to enable further functionalization of the surface. The deposition of aminophosphonates with different chain lengths (6 and 12 methylenes) was investigated. Oxygen plasma treatment proved useful in increasing the number of –OH groups at the TiO2 surface, thus helping to anchor the aminophosphonates. By combining different surface-sensitive experimental techniques, we found the existence of a discontinuous monolayer where the molecules are covalently coupled to the TiO2 surface. For the molecules with longer chains we find evidence of their covalent coupling to the surface through Ti-O-P bond formation, of the exposure of the amino groups at the outer surface, and of an increase in the order of the layer upon thermal annealing.
The morphological and mechanical properties of thiolated ssDNA films self-assembled at different ionic strength on flat gold surfaces have been investigated using Atomic Force Microscopy (AFM). AFM nanoshaving experiments, performed in hard tapping mode, allowed selectively removing molecules from micro-sized regions. To image the shaved areas, in addition to the soft contact mode, we explored the use of the Quantitative Imaging (QI) mode. QI is a less perturbative imaging mode that allows obtaining quantitative information on both sample topography and mechanical properties. AFM analysis showed that DNA SAMs assembled at high ionic strength are thicker and less deformable than films prepared at low ionic strength. In the case of thicker films, the difference between film and substrate Young’s moduli could be assessed from the analysis of QI data. The AFM finding of thicker and denser films was confirmed by X-Ray Photoelectron Spectroscopy (XPS) and Spectroscopic Ellipsometry (SE) analysis. SE data allowed detecting the DNA UV absorption on dense monomolecular films. Moreover, feeding the SE analysis with the thickness data obtained by AFM, we could estimate the refractive index of dense DNA films.
Reproducibility of results is essential for a well-designed and conducted experiment. Several reasons may originate failure in reproducing data, such as selective reporting, low statistical power, or poor analysis. In this study, we used PEG6000 samples from different distributors and tested their capability inducing spheroid formation upon surface coating. MALDI-MS, NMR, FTIR, and Triple SEC analysis of the different PEG60000s showed nearly identical physicochemical properties different, with only minor differences in mass and hydrodynamic radius, and AFM analysis showed no significant differences in the surface coatings obtained with the available PEG6000s. Despite these similarities, just one showed a highly reproducible formation of spheroids with different cell lines, such as HT-29, HeLa, Caco2, and PANC-1. Using the peculiar PEG6000 sample and a reference PEG6000 chosen amongst the others as control, we tested the effect of the cell/PEG interaction by incubating cells in the PEG solution prior to cell plating. These experiments indicate that the spheroid formation is due to direct interaction of the polymer with the cells rather than by interaction of cells with the coated surfaces. The experiments point out that for biological entities, such as cells or tissues, even very small differences in impurities or minimal variations in the starting product can have a very strong impact on the reproducibility of data.
In this study we report about the reproducibility of three-dimensional cell culture of floating cell spheroids on PEG6000 treated cell culture dishes. Three-dimensional tumour spheroids or organoids present an interesting test platform for nanoparticulated drug delivery or nanoparticle toxicity. We tested the reproducibility of spheroid formation induced by the PEG coated surface. Interestingly we found that the results were different in a reproducible manner depending on the distributors of PEG6000. Despite the nearly identical physicochemical properties of PEG6000 (MALDI-MS, NMR, FTIR, Triple SEC) with only minor differences, we observed only for one PEG6000 a highly reproducible formation of spheroids with different cell lines such as HT-29, HeLa, Caco2, and PANC-1. The surface coating with the different PEG6000 was studied by AFM. The surface coating as well as the physicochemical characterization showed only small differences in mass and hydrodynamic radius between the different PEGs. A direct coating of the cells with PEG from two distributors indicate that the spheroid formation in due to direct interaction of the polymer with the cell rather than by interaction of cells with the coated surface. The experiments point out that for biological entities, such as cells or tissues, even very small differences such as impurities or batch-to-batch variations in the purchased product can have a very strong impact.