Harinaldi Harinaldi

Harinaldi Harinaldi


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
ASAdhika Satyadharma
Adhika Satyadharma
MCMing-Jyh Chern
Ming-Jyh Chern
HKHeng-Chuan Kan
Heng-Chuan Kan
HHHarinaldi Harinaldi
Harinaldi Harinaldi
JJJames Julian
James Julian
The utilization of data in physics-informed neural network (PINN) may be considered as a necessity as it allows the simulation of more complex cases with a significantly lower computational cost. However, doing so would also make it prone to any issue with the data quality, including its noise. This study would primarily focus on developing a special loss function in the PINN to allow an effective utilization of noisy data. However, a study regarding the data location and amount was also conducted in order to allow a better data utilization in PINN. This study was conducted on a lid-driven cavity flow at Re = 200, 1000, and 5000 with a dataset of less than 100 velocity data and a maximum noise of 10% of the maximum velocity. The results show that by ensuring the data are distributed in a certain configuration, it has zero noise, and by using as much data as possible, the computational cost of PINN can be significantly reduced compared to without using any data at all. For Re = 200, it is 7.4 faster by using data, and this speedup is potentially higher for higher Re cases. For the noise in particular, it does not only make the PINN more inaccurate but also necessitate the usage of more data as this is the only way to make it more accurate. This issue though is capable to be solved with our new method, which only uses the data as an approximate solution, and the governing equation would figure out the details. This method was also shown to be capable to improve the PINN accuracy with the potential to almost completely eliminating the noise effect.

24 January 2021 in Computation
Verified
Journal Article
Open access
PDF file
ASAdhika Satyadharma
Adhika Satyadharma
HHHarinaldi Harinaldi
Harinaldi Harinaldi
Although the grid convergence index is a widely used for the estimation of discretization error in computational fluid dynamics, it still has some problems. These problems are mainly rooted in the usage of the order of a convergence variable within the model which is a fundamental variable that the model is built upon. To improve the model, a new perspective must be taken. By analyzing the behavior of the gradient within simulation data, a gradient-based model was created. The performance of this model is tested on its accuracy, precision, and how it will affect a computational time of a simulation. The testing is conducted on a dataset of 36 simulated variables, simulated using the method of manufactured solutions, with an average of 26.5 meshes/case. The result shows the new gradient based method is more accurate and more precise then the grid convergence index(GCI). This allows for the usage of a coarser mesh for its analysis, thus it has the potential to reduce the overall computational by at least by 25% and also makes the discretization error analysis more available for general usage.

16 August 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
FMFadli C. Megawanto
Fadli C. Megawanto
HHHarinaldi Harinaldi
Harinaldi Harinaldi
BUBudiarso
Budiarso
JJJames Julian
James Julian
Plasma actuator is one of the active flow control equipment that is being developed in recent years. In this study, numerical analysis is used to obtain optimization of plasma actuator that placed on airfoil at 0.21c. This numerical simulation executed at 3 (three) variations of Reynolds number, 35,000, 100,000, and 200,000 The plasma actuator was installed on an NACA 4415 with 100 mm chord length (1:1 scale) and magnetic induction (magnetohydrodynamics) is applied. The calculations of aerodynamics force, such as lift force and drag force was held to investigate the most optimal performance of plasma actuator. The results of this numerical study show that by placing plasma actuator around 0.21 from chord line, obtaining optimization in decreasing of drag coefficient and increasing of lift coefficient on 35,000 of Reynolds number. Where plasma actuator is proven to be most effective way for reducing drag coefficient at angle of attack of 15° with a percentage decrease of 15.01%. While the largest increasing of lift coefficient, 17.15% was occur at 9° angle of attack.

28 February 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
BUBudiarso
Budiarso
HHHarinaldi Harinaldi
Harinaldi Harinaldi
RKRiza Farrash Karim
Riza Farrash Karim
JJJames Julian
James Julian
Flow control on a squareback object which resembles many engineering related objects is believed to be highly beneficial. One of the flow characteristics behind the object, recirculating bubble, is known to play significant role in pressure distribution. Meanwhile, plasma actuator implementation on such object is still underdeveloped in application basis. This paper focuses on acquiring a deeper understanding of plasma actuator effect on flow phenomenon behind a squareback object, especially on its application to recirculating bubble control in order to reduce drag. The experiment was divided into drag measurement experiment and visualization experiment. The drag measurement result shows that plasma actuator succeeded on reducing drag up to 15.36% in the lowest Reynolds number. Meanwhile, the visualization experiment shows that plasma actuator has shifted the recirculating bubble position to be closer to the object’s wall.

1 May 2025 in Journal of Applied Fluid Mechanics
Verified
Journal Article
Open access
PDF file
WIW. Iskandar
W. Iskandar
JJJ. Julian
J. Julian
MAM. I. Adhynugraha
M. I. Adhynugraha
FHF. Hasim
F. Hasim
HHHarinaldi Harinaldi
Harinaldi Harinaldi
The improvement of the fluidic oscillator as an active flow control device is studied in depth. The interior geometry of the fluidic oscillator is modified by adding backward-facing step (BFS). Variations of BFS height (H) are 2, 4, 6, 8, and 10 mm. The study is carried out computationally using OpenFoam. An unstructured mesh is used in this study, with the mesh quality maintained at y+<5. The highest frequency increase occurs at BFS height of 10 mm, which is 36.45%. On the other hand, BFS also increases the average pressure drop by less than 5%, as observed across all height variations. Overall, this study suggests using BFS height of 10 mm. The increase in the momentum of the return flow within the feedback channel leads to a higher oscillation frequency of the fluidic oscillator. The increase in average pressure drop is due to the presence of a recirculation bubble right in the step.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
WAWarjito
Warjito
HHHarinaldi Harinaldi
Harinaldi Harinaldi
MSManus Setyantono
Manus Setyantono
SSSahala D. Siregar
Sahala D. Siregar
There are three sub-processes on flotation. These processes are intervening liquid film into critical thickness, rupture of liquid film forming three phase contact line, and expansion three phase contact line forming aggregate stability. Aggregate stability factor contribute to determine flotation efficiency. Aggregate stability has some important factors such as reagent and particle geometry. This research focussed on to understand effect of particle geometry to aggregate stability. Experimental setup consists of 9 x 9 x26 cm flotation column made of glass, bubble generator, particle feeding system, and high speed video camera. Bubble generator made from single nozzle with 0.3 mm diameter attached to programmable syringe pump. Particle feeding system made of pipette. Particle used in this research is taken from open pit Grasberg in Timika, Papua. Particle has sub-angular geometry and its size varies from 38 to 300 µm. Bubble-particle interaction are recorded using high speed video camera. Recordings from high speed video camera analyzed using image processing software. Experiment result shows that aggregate particle-bubble and induction time depends on particle size. Small particle (38-106 µm) has long induction time and able to rupture liquid film and also forming three phase contact line. Big particle (150-300 µm) has short induction time, so it unable to attach with bubble easily. This phenomenon is caused by apparent gravity work on particle-bubble interaction. Apparent gravity worked during particle sliding on bubble surface experience increase and reached its maximum magnitude at bubble equator. After particle passed bubble equator, apparent gravity force experience decrease. In conclusion particle size from 38-300 µm can form stable aggregate if particle attached with bubble in certain condition.