The problem of vibration and noise in the iron core of power transformers remains quite topical. Insofar as the state‐of‐the‐art iron core and binding production adopt the lamination method and weft‐free adhesive tape, respectively, the transformer core vibration is mainly attributed to the silicon steel sheet (SSS) magnetostriction. In this paper, based on the magnetostriction of grain‐oriented SSS, an in‐depth analysis of the vibration generation mechanism in the transformer core was performed. The SSS microstructure was observed, its magnetostrictive properties at different magnetic flux densities were tested, and a core‐simulating four‐corner iron core model was constructed to analyze the vibration characteristics. Modal, vibration, and noise tests were performed on an actual 110 kV transformer core under no‐load conditions. The results show that the core vibration is related to SSS’s deformation mechanism. The vibration magnitude in different core parts varies due to the magnetostriction anisotropy. The vibration in vertical to the core plane is the largest, and its magnitude in the core center is lower than those at the seams in the same plane. The core vibration and noise exhibit a significant correlation, while modal characteristics strongly influence the core vibration and noise intensity.
With the wide application of power electronic devices and nonlinear loads, the resulting inter-harmonic pollution is becoming more and more serious in the power system. As important equipment in power systems, transformers have always been the focus of research. However, there are few studies on the abnormal increase in vibration and noise caused by inter-harmonic excitation. In this work, a transformer core vibration and noise measurement platform that can generate arbitrary inter-harmonic excitations was built. The real-time vibration displacement waveforms of the core model under normal and inter-harmonic conditions were experimentally measured as well as the surrounding noise level amplitude and spectrum analysis result. The influence law of excitation of intermediate harmonic content and frequency on core vibration displacement and surrounding sound pressure level was summarized. The work of this paper lays a theoretical foundation for studying the vibration and noise of power transformers and other equipment under inter-harmonics.
7 February 2024 in International Journal of Ceramic Engineering & Science
A series of low‐carbon fly ash cenosphere plates was prepared using solid waste based cementitious material as binder through a simple process; meanwhile, effects of cenosphere's particle size and size distribution on microstructure and properties were investigated. In the range of 20–200 mesh, as particle size decreases, sound absorption performance decreases while strength improves. Appropriate particle grading can effectively improve the compressive strength, but it will lead to a significant decrease in sound absorption performance. Samples prepared from fly ash cenosphere with a particle size of 20–40 mesh show good sound absorption performance: when the cavity size is 0 mm, the maximum sound absorption coefficient is 0.64 and the average value is 0.36 in the range of 50–1 600 Hz; when the cavity size is 100 mm, sound absorption coefficient at 100 Hz is 0.47, the maximum sound absorption coefficient in the range of 50–1 600 Hz is 0.90, and the average value is 0.57 in the range of 100–500 Hz. The prepared low‐carbon fly ash cenosphere plates show excellent sound absorption performance at low‐frequency and are expected to have broad application prospects in low‐frequency noise reduction and absorption.
To suppress low frequency vibration and noise generated by power transformer in residential area and achieve environment protection standards, a double-beam metamaterial is proposed, which is fabricated through periodically coupling silicon steel sheet and aluminum beams with Belleville quasi-zero stiffness spring (BQZSS). The double-beam metamaterial can be assembled with iron core of transformers as a whole to obtain the design of a low-noise transformer. Performing static analysis, the mechanical model of BQZSS is established and the relationship between restoring force, stiffness, and displacement can be obtained. Then, the mechanical properties of BQZSS are verified with the finite element method. On this basis, the governing equations of the unit cell of the double-beam metamaterial are derived using Euler–Bernoulli beam theory. According to Bloch theorem and boundary conditions, the dispersion relation of the double-beam metamaterial is deduced, and behaviors of flexural wave propagation in beams are investigated. The effects of structure parameters on bandgaps and dispersion properties are studied, and the low frequency vibration bandgap mechanism is revealed. Finally, the frequency response function (FRF) of the double-beam metamaterial with a finite length is calculated in ANSYS to verify the bandgap characteristics given by a theoretical model. The results show that the double-beam metamaterial can yield multiple low frequency bandgaps at 100 Hz, 200 Hz, 300 Hz, and 500 Hz for suppression of flexural vibration components of transformers, which benefits from Bragg scattering (BS) and the blend of BS and LR mechanisms. The opening and closing of the low frequency bandgaps and the attenuation constants within bandgaps can be tuned by choosing parameters of beams. These findings suggest that the coupling between beams can lead to novel dispersion properties, which provides a new control approach for low frequency vibration and noise in power transformer.