We experimentally demonstrate a femtosecond mode-locked, all-fiberized laser that operates in the 2 μm region and that incorporates a saturable absorber based on a bulk-structured bismuth telluride (Bi2Te3) topological insulator (TI). Our fiberized saturable absorber was prepared by depositing a mechanically exfoliated, ~30 μm-thick Bi2Te3 TI layer on a side-polished optical fiber platform. The bulk crystalline structure of the prepared Bi2Te3 layer was confirmed by Raman and X-ray photoelectron spectroscopy measurements. The modulation depth of the prepared saturable absorber was measured to be ~20.6%. Using the saturable absorber, it is shown that stable, ultrafast pulses with a temporal width of ~795 fs could readily be generated at a wavelength of 1935 nm from a thulium/holmium co-doped fiber ring cavity. This experimental demonstration confirms that bulk structured, TI-based saturable absorbers can readily be used as an ultra-fast mode-locker for 2 μm lasers.
We experimentally demonstrate the use of a bulk-structured Bi2Te3 topological insulator (TI) as an ultrafast mode-locker to generate femtosecond pulses from an all-fiberized cavity. Using a saturable absorber based on a mechanically exfoliated layer about 15 μm thick deposited onto a side-polished fiber, we show that stable soliton pulses with a temporal width of ~600 fs can readily be produced at 1547 nm from an erbium fiber ring cavity. Unlike previous TI-based mode-locked laser demonstrations, in which high-quality nanosheet-based TIs were used for saturable absorption, we chose to use a bulk-structured Bi2Te3 layer because it is easy to fabricate. We found that the bulk-structured Bi2Te3 layer can readily provide sufficient nonlinear saturable absorption for femtosecond mode-locking even if its modulation depth of ~15.7% is much lower than previously demonstrated nanosheet-structured TI-based saturable absorbers. This experimental demonstration indicates that high-crystalline-quality atomic-layered films of TI, which demand complicated and expensive material processing facilities, are not essential for ultrafast laser mode-locking applications.
12 September 2016 in Advanced Functional Materials
We demonstrate the use of an all-fiberized, mode-locked 1.94 μm laser with a saturable absorption device based on a tungsten disulfide (WS2)-deposited side-polished fiber. The WS2 particles were prepared via liquid phase exfoliation (LPE) without centrifugation. A series of measurements including Raman spectroscopy, scanning electron microscopy (SEM), and atomic force microscopy (AFM) revealed that the prepared particles had thick nanostructures of more than 5 layers. The prepared saturable absorption device used the evanescent field interaction mechanism between the oscillating beam and WS2 particles and its modulation depth was measured to be ~10.9% at a wavelength of 1925 nm. Incorporating the WS2-based saturable absorption device into a thulium-holmium co-doped fiber ring cavity, stable mode-locked pulses with a temporal width of ~1.3 ps at a repetition rate of 34.8 MHz were readily obtained at a wavelength of 1941 nm. The results of this experiment confirm that WS2 can be used as an effective broadband saturable absorption material that is suitable to passively generate pulses at 2 μm wavelengths.
5 December 2014 in Journal of the Optical Society of America B
We conducted a numerical study to investigate the minimum modulation depth of a saturable absorber that is essentially required for stable optical pulses to be generated from a passively mode-locked fiber laser cavity. More specifically, an extended nonlinear Schrödinger equation was numerically solved in order to analyze the impact of the cavity group velocity dispersion (GVD), cavity nonlinearity, and saturation gain of an active fiber on the minimum modulation depth that is required. The net cavity GVD is shown to significantly influence the required minimum modulation depth level of a saturable absorber. A cavity with little net anomalous dispersion was found to be readily mode locked through the use of a saturable absorber with a very small amount of modulation depth. Furthermore, the reason that a fiber laser cavity with a zero cavity GVD becomes unstable and needs a much higher modulation depth was investigated, and such a condition was found to be associated with the fiber nonlinearity. The minimum modulation depth was also shown to vary according to the saturation gain level of an active fiber.