Acetaldehyde removal was carried out using non-thermal plasma (NTP) at 150 J·L−1, and plasma-driven catalysis (PDC) using Ag/TiO2/SiO2, at three different input energies—70, 350 and 1150 J·L−1. For the experimental configuration used, the PDC process showed better results in acetaldehyde (CH3CHO) degradation. At the exit of the reactor, for both processes and for all the used energies, the same intermediates in CH3CHO decomposition were identified, except for acetone which was only produced in the PDC process. In order to contribute to a better understanding of the synergistic effect between the plasma and the catalyst, acetaldehyde/catalyst surface interactions were studied by diffuse-reflectance infrared Fourier transform spectroscopy (DRIFTS). These measurements showed that different species such as acetate, formate, methoxy, ethoxy and formaldehyde are present on the surface, once it has been in contact with the plasma. A reaction pathway for CH3CHO degradation is proposed taking into account all the identified compounds in both the gas phase and the catalyst surface. It is very likely that in CH3CHO degradation the presence of methanol, one of the intermediates, combined with oxygen activation by silver atoms on the surface, are key elements in the performance of the PDC process.
15 July 2015 in The European Physical Journal Applied Physics
This paper is a preliminary study intended to straighten out the role of reactive oxygen species in the activation mechanisms occurring in a plasma driven catalysis process for acetaldehyde decomposition. For this purpose, the interaction between the surface, the pollutant and one of the main oxidative species generated by non-thermal plasma, namely ozone, was studied. Acetaldehyde catalytic ozonation over a nanostructured Ag/TiO2/SiO2 catalyst is carried out at room temperature and atmospheric pressure, and followed by diffuse reflectance infrared fourier transform spectroscopy (DRIFTS). For this, the catalyst is firstly saturated with acetaldehyde. At the end of the saturation, acetaldehyde and crotonaldehyde, its condensation product, are identified as the major adsorbed species. In a second step, the surface ozonation is carried out and three additional intermediates are identified, namely, acetone, formic acid and acetic acid. Gaseous CO, CO2, methyl formate and methyl acetate are detected at the DRIFTS outlet, evidencing the partial mineralization of the adsorbed species. A global reaction scheme is proposed for explaining the formation of those adsorbed intermediates and gaseous products. This proposed heterogeneous ozone induced chemistry has to be taken into account when associating non-thermal plasma in air to a catalyst.
Non-thermal plasma (NTP) represents a promising technological approach for the treatment of water contaminated by recalcitrant pollutants, including per- and polyfluoroalkyl substances (PFAS). The main objective of this work was to examine the degradation of perfluorooctane sulfonic acid (PFOS) using two distinct NTP reactors: in-liquid plasma (ILP), and above-liquid plasma (ALP), operated at atmospheric pressure and ambient air. A parametric study examined the influence of key operational factors on PFOS degradation, including applied voltage, frequency, conductivity, and inter-electrode distance, followed by an evaluation of degradation as a function of treatment time under selected conditions. PFOS was routinely quantified using UV-Vis spectroscopy for rapid monitoring, while PFAS degradation byproducts were identified and quantified by LC-MS/MS. Results demonstrated significantly higher degradation efficiency in the ALP reactor (up to 93%) compared to ILP (max 22%) after 60 min of treatment. ICCD imaging revealed distinct discharge morphologies in both reactors. Trace amounts of several perfluoroalkyl carboxylic acids (PFCAs; C4–C8) and a short-chain perfluorosulfonic acid (PFSA; C4) were identified as degradation byproducts. A fluorine mass balance revealed that 34% of fluorine was attributed to residual PFOS and its byproducts by the end of treatment in the ALP reactor.
1 August 2026 in Plasma Sources Science and Technology
The uniform propagation of a positive polarity surface ionization wave is achieved over liquid water, at atmospheric pressure, using nanosecond pulses with high voltage rise rates (+15 kV ns −1 ). The ring-shaped discharge propagation occurs over cm-sized surfaces and for a wide range of water conductivities (5–900 µ S cm −1 ), without any branching during the discharge propagation. To our knowledge, this is the first experimental evidence of a ringed-shape ionization wave, without any branching, over a cathode water surface. They are generated in a pin-to-water configuration with a sub-millimetre gap between the pin and the water surface. Using two pulse generators, the influence of voltage rise rate on the discharge propagation dynamics is highlighted. Fast imaging and electrical diagnostics are performed under moderate (+2 kV ns −1 ) and high (+15 kV ns −1 ) voltage rise rates. In the former case, the discharge develops in three stages already reported in the literature: 1/ discharge inception in the pin-water gap, 2/ propagation of a circular ionization wave over the water surface and 3/ splitting of the ionization wave front into multiple surface streamers. In the latter case, in contrast, the circular ionization wave does not branch and the discharge continues to propagate as a uniform ring until the voltage drops. This uniform propagation is preserved over a large range of water conductivities (5–900 µ S cm −1 ). However, the conductivity slightly influences the propagation length, speed, and energy deposition. The current findings demonstrate that the use of high-voltage nanosecond pulses with sharp rise rates prevents the development of instabilities in large-scale positive polarity discharges.