Aldin Justin Sundararaj

Dr. Aldin Justin Sundararaj


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 January 2021 in International Journal of Engine Research
Verified
Journal Article
Closed access
PDF file
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
KGK R Guna
K R Guna
MWMatthew William
Matthew William
Kerosene based hydrocarbon fuels are preferred candidates for the source of energy due to its stable properties. Based on the requirement of the combustor and the growing concern over pollutant, kerosene based fuels are modified. The fuel under investigation is a modified form of kerosene with ultra-low sulphur content. The effect of temperature on modified kerosene is studied for viscosity, surface tension, specific heat, density and ignition delay. The time delay for ignition of gas-phase mixtures of modified kerosene/oxygen have been measured using a shock tube facility. The experiments are conducted in the temperature range of 1200–1877 K, pressure range of 4–12 atm and equivalence ratio of Ø = 1.5, 1 and 0.5. The ignition delay time measurements were carried out using piezoelectric pressure transducers, which records the pressure rise due to ignition and simultaneously recording the light emission during the process of ignition using a photodiode. The ignition delay is represented as τign = 0.168841 × P−1.49 × Ø0.72 × e(14310/T)

18 April 2018 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
BPB. C. Pillai
B. C. Pillai
GAGodson Asirvatham
Godson Asirvatham

1 February 2019 in Journal of the Geological Society of India
Verified
Journal Article
Closed access
PDF file
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
BPB. C. Pillai
B. C. Pillai
KGK. R. Guna
K. R. Guna
ASA. N. Subash
A. N. Subash
AHA. P. Haran
A. P. Haran
PKPradeep Kumar
Pradeep Kumar
Shock tube facility in the Propulsion and High Enthalpy laboratory, Aerospace Engineering Department, has been extensively used to study the ignition characteristics of fuels by measuring the ignition delay times for various hydrocarbon fuels at high temperatures. Initially a systematic method has been followed to calibrate the shock tube for ignition delay time measurements by measuring the delay times of C2H6 – O2 gas mixture diluted with argon. The results show good agreement with earlier reported works of Ethane ignition. Ignition times of low molecular weight liquefied petroleum gas, a fuel used in many industrial and household applications has been studied in the temperature range of 1250-1880 K and in the pressure range of 6-11 atm at equivalence ratios (Φ = 0.5 & 1). The ignition delay was measured in the reflected shock region by recording the ignition-induced pressure rise and emission from CH radical simultaneously. From the present study it is noted that the ignition delay time for liquefied petroleum gas reduces with increase in temperature and its activation energy lies in the range of 40 kcal/mol.

1 January 2021
Verified
Journal Article
Closed access
PDF file
AAAhmed N. Al Al-Masri
Ahmed N. Al Al-Masri
HMHamam Mokayed
Hamam Mokayed
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
Martin Sagayam KulandairajMartin Sagayam Kulandairaj
Martin Sagayam Kulandairaj
Ahmed A. ElngarAhmed A. Elngar
Ahmed A. Elngar
BPB C Pillai
B C Pillai
American scientific publishing group

13 February 2026 in Combustion Engines
Verified
Journal Article
Open access
KMKesavan Marimuthu
Kesavan Marimuthu
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
ANAbhijith Girish Nair
Abhijith Girish Nair
MTMuthumari Thangapandi
Muthumari Thangapandi
Understanding the ignition characteristics of binary hydrocarbon blends is essential for designing high-speed propulsion systems such as scramjets, where ignition under short residence time is a critical challenge. In this work, the ignition delay behaviour of ethylene-acetylene/air mixtures was examined through shock tube experiments and kinetic simulations under engine-relevant conditions. Ethylene was used as the primary fuel and blended with acetylene at 5%, 10%, and 20% by volume to form binary mixtures, at an equivalence ratio of 1.0, temperatures between 560–1030 K, and pressures of 2.5–9 bar. The ignition delay time was determined from peak pressure rise and CH* chemiluminescence behind the reflected shock. Unlike previous blended fuel studies dominated by saturated hydrocarbons, this work presents a comprehensive dataset for ethylene-acetylene blends at low to intermediate temperatures and increasing the acetylene fraction from 5% to 20% reduces the ignition delay time by up to 50–60% in the 700–850 K and 2–5 bar regime. Numerical simulations were performed using ANSYS Chemkin in a closed, homogeneous, constant-volume reactor with the NUIG, ARAMCO, LLNL, and San Diego mechanisms. The sensitivity and rate-of-production analyses reveal that ignition is governed by HO2–H2O2 radical chemistry, with the thermal decomposition of H2O2 triggering rapid OH formation. Acetylene enhances ignition by promoting the regeneration of HCCO radicals and accelerating the transition to chain-branching chemistry.

1 August 2023 in Research Square
Verified
Preprint
Open access
PDF file
ASAldin Justin Sundararaj
Aldin Justin Sundararaj
SVS Venkatachalam
S Venkatachalam
ALAnton Savio Lewise
Anton Savio Lewise
RRR A Rakhi
R A Rakhi
Over a period of time, the impact of shock waves on human bodies and structures has been studied. To understand the shock wave mitigation over confined volume and porous material, an experimental study is carried out using a shock tube. For the current study, shock velocities ranging from 500 m/s to 650 m/s are created in the tube. The normal shock pressure ranged from 1.1 to 2.8 bar, and the reflected shock pressure ranged from 4.3 to 8 bar in the closed tube. High-frequency PCB pressure transducers is used to measure shock pressure. Three different methods are studied to understand the shock wave mitigation through a confined volume. The methods are perforated bodies with 30%, 40%, and 50% of circular cross section on one side and closed at other end, porous compressible materials kept outside the shock tube to understand head on collision of shock wave and head on shock wave impact on porous material sandwich between the two plates. The number of times the shockwave travelled is highest in the least porous material. On direct shock impact porous compressible material such as glass wool foam, rubber foam is observed to be shredded off, whereas polyurethane foam was comparatively stable. When sandwiching between the two thin plates, it is observed that the shock loading is more on the glass wool foam, less on the rubber foam and the least on the polyurethane foam. It can be concluded that shock waves can be attenuated by perforating bodies, and further impact of the shock can be reduced by materials having blast mitigation properties.