Over time, oil production in a reservoir tends to decrease, which makes it difficult to flow through the reservoir to the well, making its production increasingly difficult and costly. Due to their physical properties, such as reducing the water/oil interfacial tension, surfactants have been used in enhanced oil recovery (EOR) processes, however, their adsorption presents as an undesirable and inevitable factor and can decrease the efficiency of the method. This work’s main objective is to evaluate the effect of glycerol in the adsorption of surfactants in sandstones, as well as in the recovery factor during EOR. Brine solutions containing the nonionic surfactant saponified coconut oil (SCO), with and without glycerol, were used in the adsorption and oil recovery tests in sandstone. Adsorption, recovery, rheological, and thermogravimetric analysis were carried out. Regarding the surfactant/glycerol/brine solution, there was an improvement in the oil mobility, as the glycerol contributed to an increase in the viscosity of the solution, thereby increasing the sweep efficiency. The recovery factor obtained for the surfactant solution with glycerol was satisfactory, being 53% higher than without glycerol, because it simultaneously provided an increase in viscosity and a decrease in interfacial tension, both of which are beneficial for the efficiency of the process.

Oil well cleanup fluids (pre-flushes) are intermediate fluids pumped ahead of the cement slurry; they are able to clean the well walls by removing the filter cake formed by the drilling fluid, and leave the surface water-wet. This work’s main objective was to use biodegradable microemulsion systems as cleanup fluids in order to reduce the environmental impact. Three microemulsion systems were formulated, each composed of an oil phase, a surfactant and three different aqueous phases: glycerol, glycerol:water (mass ratio 1:1), and fresh water. The results show that all microemulsion systems were effective with 100% filter cake removal, with a removal time of less than 60 s. The wettability test and fluid compatibility analyses exhibited advantageous performances, without phase separation, variations in viscosity, gelation, or flocculation. The compressive strength and X-ray diffractometry (XRD) analysis showed the influence of the glycerol on the cement slurry properties, with the compressive strength resistance ranging from 8.0 to 10.7 MPa, and resulted in the formation of portlandite.

Microemulsion is a thermodynamically stable dispersion consisting of an aqueous and an organic phases, both stabilized by surfactant molecules and when in need, co-active surfactant. The nature and structure of these components are essential in the formulation of microemulsified systems. For this, the construction of phase diagrams can be a fundamental tool to characterize the ideal experimental conditions for the existence and operation of microemulsions. Thus, the present work had as objective to obtain a comparison between microemulsions with different compositions through the construction of ternary diagrams, aiming to achieve the most stable system. To produce microemulsified systems, a non-ionic surfactant (Ultranex NP 60), a co-surfactant (Isopropyl Alcohol), two organic phases (pine oil and castor oil) and an aqueous phase (glycerin solution) were used. Also complementing the study, rheological tests of the oleic phases were accomplished, as well as their thermogravimetric analysis. The focus of the reached ternary diagrams was to find the system with the largest Winsor type IV region (microemulsion). It was verified this region had a significant increase by the addition of the co-surfactant in the medium and using a vegetable oil, such as pine oil, since it promotes strong surfactant-oil interactions on the interface.

Cementing operations are among the most critical steps in oil-well construction. When performed improperly, the integrity and useful life of the well can be significantly compromised. Light cement pastes are used to cement formations with a low fracture gradient to ensure zonal isolation and maintain the integrity of the casing. Extenders are additives used to reduce the density of cement pastes, ensuring that the paste has desirable properties before and after setting. This work aimed to evaluate the application of palygorskite clay as an additive in lightweight cement pastes for oil wells, highlighting how its fibrous morphology influences the microstructure and enhances the macroscopic properties of the hardened cement matrix. For this, the clay sample was initially characterized regarding its physicochemical properties using X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetry (TG), textural analysis (BET/N₂), and scanning electron microscopy (SEM). Lightweight pastes (1.56 g/cm³) were then formulated, varying the clay concentration by 1%, 3%, and 6% of the total mass. Cement pastes using bentonite were also formulated for comparison. Technological tests of atmospheric consistency, rheological behavior, free water, and stability were applied. It can be noted that the pastes formulated with palygorskite had lower viscosity, reflected in the reduced plastic viscosity and yield stress values, indicating easier flow behavior when compared with bentonite-based pastes. The pastes formulated with 6% palygorskite and 3% bentonite showed satisfactory stability and drawdown results. Therefore, applying palygorskite satisfies the minimum requirements for acting as an extending agent for lightweight cement pastes and is an option for application in oil-well cementing operations.