École Supérieure d’Électronique de l'Ouest (ESEO), Department of Electrical and Control Engineering, 10 Boulevard Jeanneteau CS 90717, 49107 Angers CEDEX 2, France
Prof. Dr. Mohsen Koohestani
École Supérieure d’Électronique de l'Ouest (ESEO), Department of Electrical and Control Engineering, 10 Boulevard Jeanneteau CS 90717, 49107 Angers CEDEX 2, France
A compact asymmetric coplanar strip (ACS)-fed monopole antenna is presented, which operates within the Bluetooth and UWB frequency bands with the capability to simultaneously reject the lower WLAN interfering band. The antenna consists of an inverted right triangle patch monopole loaded by open-ended L-shaped slits not only to produce the additional 2.4 GHz passband to the UWB design but also to achieve stopband characteristics around 5.2 GHz. The conceptual equivalent circuit model as well as characteristic mode analyses are carried out in the design evolution process. The proposed antenna has an overall size of only 20 mm × 10 mm, having the smallest area among the so far developed designs, which can be easily integrated within any wireless gadgets. A prototype is fabricated and measured to validate the design, demonstrating the predicted behavior fairly achieved by full-wave analysis. The antenna –10 dB operating bandwidth ranges from 2.38 to 2.42 GHz and from 3.35 to 11 GHz while rejecting from 4.69 to 5.2 GHz. Unlike the unwanted stopband, where the radiation characteristics are adequately deteriorated, the proposed antenna fairly provides stable omni-directional radiation patterns in the H -plane, and has an average efficiency (gain) of 87.3% (2.6 dBi) in the desired passband. As far as the antenna transient behavior is concerned, an adequate measured (simulated) system fidelity factor of 0.7 (0.68) is achieved for the transmission of impulse-type UWB signals in the face-to-face configuration.
23 June 2020 in IEEE Transactions on Electromagnetic Compatibility
This article presents a comprehensive study of the use of small-sized frequency selective surfaces (FSS) to selectively shield pocket-sized devices against EM disturbances. A typical use case is to protect a 2.4-GHz transceiver (e.g. WiFi/Bluetooth) against ISM/GSM disturbances (around 868/915 MHz), using an 8.2 – 4.1 cm FSS structure. A detailed comparison is drawn between results in real and emulated far-fields for different FSS-to-antenna distances (5 and 25 mm), which is further confirmed by emission measurements employing an open transverse electromagnetic cell. Results demonstrate, in line with full-wave simulations including calculated Poynting integrals, that such a FSS can effectively reduce power by about 5 dB in the stopband, while providing no attenuation in the passband and is small enough for an easy integration. Moreover, it is shown that the farther the FSS from the antenna, the closer the results to a no-FSS scenario. This provides an insight to reconsider FSSs for the shielding of mobile and/or smart devices.
5 October 2016 in IEEE Transactions on Microwave Theory and Techniques
A methodology for the design of printed magnetically coupled resonant wireless power-transfer (WPT) systems is proposed. The design methodology aims at a well-matched system with a maximized power-transfer efficiency for mid-range applications. The system consists of two identical resonant coils driven by high-quality factor loops. The proposed design criteria allows obtaining maximum achievable transfer efficiency and impedance matching at any defined distance without any external matching circuits connected to the driven loops. For validation purposes, a printed WPT system at 10 MHz is fabricated targeting 1-m distance between the transmitting and receiving sides. Its performances in terms of reflection and transmission coefficients, as well as in terms of generated electric and magnetic fields, have been characterized numerically and experimentally. The impact of human body presence on the system has also been investigated observing the splitting in two frequencies of the common resonant frequency of the coils. A dosimetric study has been conducted using a detailed high-resolution anatomical human body model and considering E 99 , J 1 cm 2 , and specific absorption rate (SAR) (local and whole body averaged SAR) as exposure metrics. It has been observed that peak exposure levels appear in different tissues depending on the body location. Compliance with the international commission on nonionizing radiation protection (ICNIRP) reference level as well as basic restrictions has been studied followed by computing the maximum allowable input power. It has been found that, with the body located 1 m away from the transmitting coil, the maximum allowable input power satisfying E 99 is in the order of MW, whereas it reduces to tens of kilowatt when considering SAR and J1 cm 2 . The latter has been noticed to be the most restrictive dosimetric quantity.
1 March 2011 in International Journal of RF and Microwave Computer-Aided Engineering
An ultra-thin double-functional metasurface patch antenna (MPA) was proposed, where it can operate not only in the antenna mode but also can simultaneously act as perfect absorber for normal incident waves, suitable for RFID applications in the 868 MHz band. The MPA structure consists of a typical coaxially-fed patch antenna merged, for the first time, with a metasurface absorber acting as artificial ground. A methodology for the unit-cell design of the metasurface is proposed followed by an equivalent circuit model analysis, which makes it possible to transform a low-loss ( $$tan\delta =0.0015$$ ) unit-cell with highly-reflective characteristics to a perfect absorber for normal incident waves. It is based on modifying the critical external coupling by properly introducing slits on the unit-cell, allowing to design an ultra-thin ( $$\lambda _0/225$$ at 868 MHz) and a very compact structure in comparison to previously developed designs. For validation purposes, the MPA was fabricated and its performances in both functional modes were characterized numerically and experimentally. It is demonstrated that merging the absorber with the patch not only allows obtaining a well-matched ( $$|S_{11}|<-30$$ dB) antenna with an enhanced gain (by 175.6% compared to a typical patch) at the desired frequency but also leads to an overall thickness of only 2.5 mm ( $$\lambda _0/138.1$$ at 868 MHz). With an absorber size limited to the MPA dimensions, a reasonable 1.3 dB reduction in powers reflected by the MPA was achieved compared to a similar size metallic sheet. Whilst having the lowest profile among the so far reported RFID readers, the proposed MPA can be conveniently fitted for example within the required volume of smart shelf RFID readers or used in portable RFID readers while being capable of mitigating multipath reflection issues and incorrect reading of RFID.