Stephan Bechtel

Mr. Stephan Bechtel

Saarland University
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
SBStephan Bechtel
Stephan Bechtel
MMMirko Meisberger
Mirko Meisberger
SKSamuel Klein
Samuel Klein
THTobias Heib
Tobias Heib
SQSteven Quirin
Steven Quirin
HHHans-Georg Herrmann
Hans-Georg Herrmann
Using additive manufacturing to generate a polymer–metal structure offers the potential to achieve a complex customized polymer structure joined to a metal base of high stiffness and strength. A tool to evaluate the generated interface during the process is of fundamental interest, as the sequential deposition of the polymer as well as temperature gradients within the substrate lead to local variations in adhesion depending on the local processing conditions. On preheated aluminum substrates, 0.3 and 0.6 mm high traces of polylactic acid (PLA) were deposited. Based on differential scanning calorimetry (DSC) and rheometry measurements, the substrate temperature was varied in between 150 and 200 °C to identify an optimized manufacturing process. Decreasing the layer height and increasing the substrate temperature promoted wetting and improved the adhesion interface performance as measured in a single lap shear test (up to 7 MPa). Thermographic monitoring was conducted at an angle of 25° with respect to the substrate surface and allowed a thermal evaluation of the process at any position on the substrate. Based on the thermographic information acquired during the first second after extrusion and the preset shape of the polymer trace, the resulting wetting and shear strength were estimated.

25 October 2016 in RSC Advances
Verified
Journal Article
Open access
PDF file
MZMarco Zeiger
Marco Zeiger
SFSimon Fleischmann
Simon Fleischmann
BKBenjamin Krüner
Benjamin Krüner
ATAura Tolosa
Aura Tolosa
SBStephan Bechtel
Stephan Bechtel
VPVolker Presser
Volker Presser
Manganese oxide presents very promising electrochemical properties as an electrode material in supercapacitors, but there remain important open questions to guide further development of the complex manganese oxide/carbon/electrolyte system. Our work addresses specifically the influence of carbon ordering and the difference between outer and inner porosity of carbon particles for the application in aqueous 1 M Na2SO4 and 1 M LiClO4 in acetonitrile. Birnessite-type manganese oxide was hydrothermally hybridized on two kinds of carbon onions with only outer surface area and different electrical conductivity, and conventional activated carbon with a high inner porosity. Carbon onions with a high degree of carbon ordering, high conductivity, and high outer surface area were identified as the most promising material, yielding 179 F g−1. Pore blocking in activated carbon yields unfavorable electrochemical performances. The highest specific energy of 16.4 W h kg−1 was measured for a symmetric full-cell arrangement of manganese oxide coated high temperature carbon onions in the organic electrolyte. High stability during 10 000 cycles was achieved for asymmetric full-cells, which proved as a facile way to enhance the electrochemical performance stability.

26 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
SBStephan Bechtel
Stephan Bechtel
RSRouven Schweitzer
Rouven Schweitzer
MFMaximilian Frey
Maximilian Frey
Ralf BuschRalf Busch
Ralf Busch
HHHans-Georg Herrmann
Hans-Georg Herrmann
Generating polymer–metal structures by means of additive manufacturing offers huge potential for customized, sustainable and lightweight solutions. However, challenges exist, primarily with regard to reliability and reproducibility of the additively generated joints. In this study, the polymers ABS, PETG and PLA, which are common in material extrusion, were joined to grit-blasted aluminum substrates. Temperature dependence of polymer melt rheology, wetting and tensile single-lap-shear strength were examined in order to obtain appropriate thermal processing conditions. Joints with high adhesive strength in the fresh state were aged for up to 100 days in two different moderate environments. For the given conditions, PETG was most suitable for generating structural joints. Contrary to PETG, ABS–aluminum joints in the fresh state as well as PLA–aluminum joints in the aged state did not meet the demands of a structural joint. For the considered polymers and processing conditions, this study implies that the suitability of a polymer and a thermal processing condition to form a polymer–aluminum joint by material extrusion can be evaluated based on the polymer’s rheological properties. Moreover, wetting experiments improved estimation of the resulting tensile single-lap-shear strength.

1 January 2019 in Procedia Manufacturing
Verified
Journal Article
Open access
JKJerome Kaspar
Jerome Kaspar
SBStephan Bechtel
Stephan Bechtel
THTobias Häfele
Tobias Häfele
FHFranziska Herter
Franziska Herter
JSJan Schneberger
Jan Schneberger
MVMichael Vielhaber
Michael Vielhaber

1 February 2020 in Thin Solid Films
Verified
Journal Article
Closed access
SBStephan Bechtel
Stephan Bechtel
CNChristophe Nies
Christophe Nies
FFFrank Fug
Frank Fug
SGSamuel Grandthyll
Samuel Grandthyll
FMFrank Müller
Frank Müller
WPWulff Possart
Wulff Possart