Inkjet printing of two-dimensional (2D) material has been a center of interest for wearable electronics and has become a promising platform for next-generation technologies. Despite the enormous progress made in printed 2D materials, there are still challenges in finding the optimal printing conditions involving the ink formulation and printing parameters. Adequate ink formulation and printing parameters for target 2D materials rely on empirical studies and repeated trials. Therefore, it is essential to compile promising strategies for ink formulation and printing parameters. In this context, this review discusses the optimal ink formulations to prepare stable ink and steady ink jetting and then explores the critical printing parameters for fabricating printed 2D materials of a high quality. The summary and future prospects for inkjet-printed 2D materials are also addressed.

Water pollution is a growing global issue; there are many approaches to treating wastewater, including chemical coagulation, physical adsorption, and chemical oxidation. The photocatalysis process has provided a solution for removing pollutants from wastewater, where the pair of the photoelectron and hole works through an asymmetric way to degrade the contaminants under UV irradiation. This method offers an alternative route for treating the pollutant with a lower energy cost, high efficiency, and fewer byproducts. A continuous-flow microfluidic reactor has a channel size from tens to thousands of micrometers, providing uniform irradiation and short diffusion length. It can enhance the conversion efficiency of photocatalysis due to the simple spatial symmetry inside the microreactor channel and among the individual channels. In addition, the bandgap of TiO₂, ZnO, or other photocatalyst nanoparticles with symmetric crystal structure can be modified through doping or embedding. In this mini-review, a review of the reported continuous-flow photocatalytic microfluidic reactor is discussed from the perspective of both microreactor design and material engineering.

Biofouling is a significant problem in the aquaculture and marine shipping industries; thus, various antifouling methods have been developed to prevent the resultant economic losses. In the present study, the superhydrophobic surface of a lotus leaf was bio-mimicked to achieve antifouling. Specifically, fabric substrates with and without superhydrophobic coatings on the surface were installed on the Tongyeong yacht in December 2020 (group A) and April 2021 (group B), and the coverage of the attached invertebrates was recorded every month until August 2021. The coverage of solitary ascidians (Ascidiella aspersa and Ciona robusta) and branching bryozoans (Bugula neritina) was lower on the coated substrates than on the non-coated ones, and coating or non-coating was significantly correlated with the extent of coverage. Superhydrophobic substrates with a low surface energy and micro–nano dual structure may be unsuitable for the attachment of larvae. Therefore, superhydrophobic coating is a more effective and simpler method of antifouling for certain taxa than other antifouling strategies. However, the antifouling effect of the superhydrophobic substrate in group A reduced after 5 months from the first installation; thus, the durability of the antifouling coating should be further improved, and solving this problem remains a major task, necessitating further research.

Since the discovery of graphene, there has been increasing interest in two-dimensional (2D) materials. To realize practical applications of 2D materials, it is essential to isolate mono- or few-layered 2D nanosheets from unexfoliated counterparts. Liquid phase exfoliation (LPE) is the most common technique to produce atomically thin-layered 2D nanosheets. However, low production yield and prolonged process time remain key challenges. Recently, novel exfoliation processes based on microfluidics have been developed to achieve rapid and high yield production of few-layer 2D nanosheets. We review the primary types of microfluidic-based exfoliation techniques in terms of the underlying process mechanisms and the applications of the 2D nanosheets thus produced. The key challenges and future directions are discussed in the above context to delineate future research directions in this exciting area of materials processing.

Ag–ZnO nanocomposite films have been widely employed as a promising photocatalyst displaying excellent charge separation and broadband absorption under illumination. Although a variety of synthetic methods have been proposed, the preparation of nanocomposite films with controlled morphology in a single process has been rarely attempted. Here, we introduce a facile and rapid synthetic method to fabricate Ag–ZnO nanocomposite films with controlled morphology by using a microreactor-assisted solution deposition (MASD) process. The nanocomposite film could be formed in a single process within 10 min, which is enabled by rationally designing the MASD process. In addition, by simply tuning in situ growth kinetics of ZnO nanostructures in the process, the morphology of the Ag–ZnO nanocomposite film is varied, including flower- and nanorod-structures. The enhanced photocatalytic activity of the Ag–ZnO nanocomposite film over its pristine ZnO counterpart is demonstrated by performing photoelectrochemical (PEC) measurements.