Waste ceramic concrete (WOC) made from waste ceramic floor tiles has several economic and environmental benefits. Fire is one of the most common disasters in buildings, and WOC is a brittle construction material; therefore, the mechanical properties of WOC structures under high temperatures should be considered. According to previous studies, hybrid fiber can further reduce damage to concrete under high temperatures. Meanwhile, crack width and propagation are among the key characteristics of concrete materials that need to be considered, but few studies have focused on their behavior when subjected to elevated temperatures. The new concrete materials proposed by the authors are WOC and WOC-Hybrid. WOC was prepared with Natural Coarse Aggregates (NCA), Natural Fine Aggregate (NFA), Ordinary Portland Cement (OPC 43 grade), and ceramic waste tiles with 20% replacements for coarse aggregates, 10% replacements for fine aggregates, and 10% replacement for cement. In contrast, WOC-Hybrid was prepared with the addition of hybrid fiber (1% crimped steel fiber and 1% polyvinyl alcohol fiber) in WOC. The specimens were exposed to temperatures of 100–300 °C, and then the specimens were tested for tensile and compressive strength. The present study aims to find a new method to improve concrete resistance to elevated temperatures at the lowest costs by experimental and computational analysis via machine learning models. The application of machine learning models such as artificial neural networks (ANN) and multiple linear regression (MLR) was employed in this study to predict the compressive and tensile strength of concrete. The linear coefficient correlation (R2) and mean square error (MSE) were evaluated to investigate the performance of the models. Based on the experimental analysis, the results show that the effect of hybrid fiber on the crack width and propagation is greater than that on the crack width and propagation of WOC and PC after exposure to high temperatures. However, the enhanced effect of hybrid fiber on the mechanical properties, rack width, and propagation decreases after subjecting it to a high-temperature treatment, owing to the melting and ignition of hybrid fibers at high temperatures. Regarding the computational analysis, it was found that the developed MLR model shows higher efficiency than ANN in predicting the compressive and tensile strength of PC, WOC, and WOC-Hybrid concrete.
Ultrasonic pulse velocity (UPV) and rebound hammer tests are accepted as alternatives to destructive testing to determine the compressive strength, dynamic modulus of elasticity, and Poisson’s ratio, which are needed for structural design. Although much work has been conducted for plain concrete, the research data for fibre-reinforced concrete (FRC) is insufficient. In this regard, this study explains the correlations between compressive strength, rebound hammer, and UPV tests for plain concrete and FRC contains 0.25%, 0.50%, and 1.00% of 30 mm and 50 mm long steel fibres. A total of 78 concrete cube and beam specimens were tested by direct, semi-direct, and indirect UPV and rebound hammer test methods. The study found that the rebound hammer test is more suitable for measuring the compressive strength of matured FRC than young concrete. The UPV test revealed that the volume fraction does not, but the length of steel fibres does affect the UPV results by the direct test method. The UPV direct method has the highest velocity, approximately two times the indirect velocity in FRC. UPV measurements can be effectively used to determine the dynamic modulus of elasticity and Poisson’s ratio of FRC. The dynamic elastic modulus increases while the Poisson’s ratio decreases for the same steel fibre length when at increasing FRC fibre content. The results of this study will be significant for non-destructive evaluations of FRC, while additional recommendations for future studies are presented at the end of the paper.
Construction and demolition (C&D) waste was considered as zero value materials and, as a result, most C&D waste materials ended up in landfills, eventually constituting environmental issues. Therefore, it is important to explore the potential of such C&D waste materials for concrete production. Thus, this research effort aims to find a new method to improve sustainable concrete properties exposed to elevated temperatures at the lowest costs and identify the relationship between temperature change and a change in colour in a heat-exposed concrete structure. Therefore, this study explored the behaviour of three types of concrete: plain concrete (PC), waste ceramic optimal concrete (WOC), and waste ceramic optimal concrete reinforced by hybrid fibre (WOC-Hybrid) in ambient and elevated temperature. The study shows that colour change in a concrete structure exposed to high temperature has a consistent relationship, where it has been found that the colour alteration is of great interest because its appearance usually coincides with the onset of a significant loss of concrete strength as a result of elected temperatures. Overall, it can be considered that waste ceramic materials reinforced by hybrid fibres can be used for concrete production, and by doing so, the negative impact of these wastes on the environment can be controlled as well as fortify the mechanical properties.
22 October 2024 in Construction and Building Materials
Non-destructive tests (NDTs) represent one of the solutions that aid engineers in evaluating the strength of materials. However, the results obtained using such tests are still questionable as they may be affected by different factors. One of these factors is the presence of steel reinforcement in concrete. An experimental investigation is presented in this study to investigate the effect of the single reinforcement steel bar on ultrasonic pulse velocity (UPV). Seven concrete beams, one containing no steel and the other six beams containing varying bar diameter and cover thicknesses, were tested. UPV measurements were obtained using the indirect method and then modified to eliminate the effect of the steel bar. To provide the scientific evidence to give a reliable and reasonable solution, a statistical analysis was also conducted. The results show that a large bar diameter and a small cover thickness significantly influence the measured UPV. Measured UPV with a spacing between transducers up to 500 mm can effectively be used to predict the compressive strength of concrete after the modification of the initial UPV.
17 July 2025 in Construction and Building Materials