Climate control systems have a largely negative effect on the energy consumption of electric vehicles and consequently on their real driving range. Improving the efficiency of climate control systems requires advanced simulation tools for an accurate evaluation of both the energy savings and thermal comfort of innovative heating and cooling solutions. In this study, the advancements beyond the state of the art consists primarily of the methodology tackling the reduction of computational costs of intensive computational fluid dynamics (CFD) simulations and/or time-consuming experimental investigations and the simultaneous assessment of vehicle cabin thermal comfort and energy flows. The approach was validated against climatized chassis dyno measurements from the EU Horizon 2020 research project QUIET. Indeed, all the considered locations within the cabin were properly validated, both in steady state and transient conditions with the largest deviations at steady state below 3 °C. Additionally, the validation results show a perfect agreement for the average cabin predicted mean vote (PMV) value and a largest deviation in terms of the PMV for the other locations below 0.3. Furthermore, the applicability of the methodology is proved with the help of its application on a parametric study for which various cabin temperature setpoints and heating, ventilation and air conditioning (HVAC) modes were simulated in winter operation.
Thermal management systems of passenger vehicles are fundamental to provide adequate cabin thermal comfort. However, for battery electric vehicles they can use a significant amount of battery energy and thus reduce the real driving range. Indeed, when heating or cooling the vehicle cabin the thermal management system can consume up to 84% of the battery capacity. This study proposes a model-based approach to design an energy-efficient control strategy for heating electric vehicles, considering the entire climate control system at different ambient conditions. Specifically, the study aims at reducing the energy demand of the compressor and water pumps when operating in heat pump mode. At this scope, the climate control system of the reference vehicle is modelled and validated, enabling a system efficiency analysis in different operating points. Based on the system performance assessment, the optimized operating strategy for the compressor and the water pumps is elaborated and the results show that the demand-based control achieves up to 34% energy reduction when compared to the standard control.
Battery electric vehicles (BEVs) are one promising approach to mitigating local greenhouse gas emissions. However, they still lag behind conventional vehicles in terms of maximum driving range. Using the heating, ventilation, and air-conditioning (HVAC) system reduces the maximum driving range of the vehicle even further since the energy for the HVAC system must come from the battery. This work investigates the impact of (1) an air–air heat exchanger and (2) an improved thermal insulation of a truck cabin on the heating performance of the HVAC system. Additionally, the required fresh-air volume flow rate to keep the CO2 level within the truck cabin below the critical value of 1000 ppm is factored in. The results show that the two simple measures proposed could increase the energy efficiency of the truck’s HVAC system by 22%. When two persons are present in the truck cabin, a fresh-air volume flow of around 100 m3/h is required to keep the CO2 concentration around 1000 ppm. These results prove that, even with simple measures, the energy efficiency of vehicles’ subsystems can be increased. In the future, more research will be necessary to further improve the energy efficiency of other vehicular subsystems.
11 December 2024 in Engineering Modelling, Analysis and Simulation
This paper presents the numerical analysis of the thermal performance of a truck cabin. The results obtained for a standard truck cabin setup are compared to the configurations with energy saving measures implemented. As a very promising energy efficiency measure, the application of the infrared panels is considered. Based on the radiative heat transfer mechanism, the infrared panels influence directly all inner cabin surfaces. This includes also the truck cabin occupants, whose perception of the indoor comfort reaches neutral values much faster and at lower ambient air temperatures. As a result, there is much lower energy demand for the cabin heating, required for maintaining the desired indoor comfort. The preliminary numerical analysis indicates the energy saving potential of around 30% for this innovative cabin thermal concept, as compared to the original energy demand for the traditional cabin heating configuration.
To reduce emissions in the existing transportation system and lower carbon dioxide (CO2) output, battery electric vehicles (BEVs) offer a promising approach due to their higher energy efficiency. However, their driving range still falls short compared to conventional vehicles. Optimizing the heating, ventilation, and air conditioning (HVAC) system can help save energy and improve passenger comfort. This study investigates an advanced thermal management system for an electric truck cabin with heating panels and added insulation. A one-dimensional (1D) cabin thermal model was also developed and validated with experimental data. The model integrates insulation, heating panels, and a 1D comfort simulation. It is functional mock-up unit (FMU) compatible and connects to larger system simulations and real-time applications. The results show that energy consumption can be reduced by up to 50% with these thermal measures. In the future, further research and new approaches will be necessary to identify even more efficient subsystems and cost-effective solutions.
To reduce emissions in the existing transportation system and lower CO2 output, battery electric vehicles (BEVs) offer a promising approach due to their higher energy efficiency. However, their driving range still falls short compared to conventional vehicles. Optimizing the heating, ventilation, and air conditioning (HVAC) system helps to save energy and improve passenger comfort. This work investigates an advanced thermal management system for an electric truck cabin, equipped with heat panels and additional insulation. First, a 1D model of the thermal management system was developed to investigate and properly size the thermal measures. The simulations enabled initial sizing and provided a first evaluation of the concept truck cabin. Subsequently, the prototype truck cabin was tested in different configurations and under varying ambient conditions in a climatic chamber and laboratory. Using the experimental data, the 1D model was optimized and validated, making it possible to simulate real-world scenarios. In the future, further research and new approaches will be necessary to identify even more efficient subsystems and cost-effective solutions.